Korg V2 manual In-Track Sampling, Performing in-track sampling, Listen to the sampled data

Page 34

If “Convert to Program” is not checked, you can listen to the sample by selecting and playing it in Sampling mode.

3. In-Track Sampling

The In-Track Sampling function samples an external audio signal from AUDIO INPUT etc. into sample memory (RAM) in synchronization with song playback, and also automati- cally creates note data in a MIDI track. The sampled audio data can easily be played from the MIDI track or edited. (☞BG p.115)

The “In-Track Sampling” radio button automatically makes the appropriate settings for this function.

Use INDIV. 1/2 OUT to monitor the audio signal being recorded. Connect the AUDIO OUTPUT MAIN L, R, INDIV1, and 2 jacks to your mixer so that you can mon- itor the output.

■Setup

1Select “Auto Sampling/HD Audio Setup” to open the dialog box.

2Use the radio buttons to select In-Track Sampling.

3In “Source Audio,” select the external audio input source.

Analog: Selects the analog audio signal from a musical instrument or other device connected to the AUDIO INPUT 1 and AUDIO INPUT 2 jacks.

S/P DIF: Selects the digital audio signal from an instru- ment or DAT deck etc. connected to the S/P DIF jack. mLAN: Selects the digital audio signal from an instru- ment etc. connected to the mLAN connector (if the optional EXB-mLAN is installed). (☞PG p.4, PG p.56 “Input”)

If “Source Audio” is set to S/P DIF or mLAN, set “Sys- tem Clock” (Global P0: 0–2a☞PG p.138) to the appro- priate system clock setting.

4Use “Mono-1/Mono-2/Stereo”to specify the mono/ste- reo status of the input source. (☞PG p.4, PG p.56) Mono-1:Use Input 1.

Mono-2:Use Input 2.

Stereo: Use Input 1 and 2 in stereo.

5Use “To” to select the MIDI track that will be used for in- track sampling. Note data will automatically be created in the MIDI track you select.

6Use “Program” to specify the program that will be cre- ated. After sampling, a new multisample will automati- cally be created, and the sampled data will be converted into a program.

7Press the OK button to execute “Auto Sampling/HD Audio Setup.” If you decide to cancel, press the Cancel button. (For the automatically-set parameters and their values, refer to p.32. For an example of using the auto- matically-set parameters ☞BG p.115)

■Performing in-track sampling

8Use “Location” to specify the playback location of the song.

9Press the SAMPLING [REC] key. (Sampling-standby)

0Press the SEQUENCER [START/STOP] key.

AAt the moment you want to start sampling, press the SAMPLING [START/STOP] key.

BPlay the instrument or other source you connected to the AUDIO INPUT jack selected in “Source Audio.”

CWhen you are finished playing, press the SAMPLING [START/STOP] key. (Only sampling will stop.) Alterna- tively, press the SEQUENCER [START/STOP] key. (Song playback and sampling will both stop.)

If you want to continue sampling while the song plays, turn the Global P0: Input/Sampling “Auto Optimize RAM” setting Off. (☞PG p.140)

If you set “Save to” to RAM (Convert to Program) and continue sampling without changing the settings, the samples will be automatically assigned to C#2, D2, ...

■Listen to the sampled data

•Move the “Location” back, and press the SEQUENCER [START/STOP] key to play back the song.

•Use “Track Select” (0–1a ☞PG p.50) to select the track specified in “To” (step 5), and play the C2 note of the keyboard.

If you want to apply an insert effect to the input source, go to the Sequencer P0: Play/REC Sampling/HD Audio page and set Input 1, 2 “Bus (IFX/Indiv.) Select” to IFX1–IFX5. Set the “BUS Select” following that insert effect to 1/2.

If you set “Trigger” (0–7b ☞PG p.56) to Threshold, sampling will begin when the input level exceeds the specified value. (☞BG p.115)

Use the page menu command “Select Bank & Smpl No.” (0–7A ☞PG p.56) to select the sampling-destina- tion sample memory (RAM).

Sequencer

29

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Update guide Table of Contents Combination mode Global modeSampling mode Program modeHow this manual is organized About this manualConventions in this manual Page Introduction Sequencer modeNew functions in version Other new functions Installing the system Updating the Triton Studio operating systemPage HD Audio Recording Sequencer modeAbout the HD Audio Track function About the audio tracks Audio Track 1&2 Erase Measure Preparing to record an audio track Specify the location where the Wave file will be savedRecording an audio track Create a directory in which to save the filesRecord the audio track SetupConnect your guitar Record Set the recording levelPress the Sequencer REC/WRITE key Punch In checked Punch In Mode Auto Using punch-in recordingCheck the recorded content Press the Sequencer START/STOP key to stop recordingCompare the recorded content Performing bounce recordingWhen you have finished setting your levels, stop play- back Track Select Menu commandsSequencer P0 Play/REC 1D Delete Song7b Ctrl Control Sampling/HD Audio7a Input COMBI, PROG, SEQ, S.PLAY, Disk 7c Recording Level dBAuditioning the contents of a Wave file Menu Command7B Sel Dir/WAVE Audio Track 7C Auto Sampling/HD Audio Setup 7D Bounce All Tracks To SongPunch Off, On Punch In Mode Manual, AutoPreference Bounce Off, OnChanges to the page menu commands Sequencer P1 Cue ListTrack and Map New page menu commandsSequencer P5 Track Edit 1R Put Wave1T Volume Ramp 1S Normalize/Level Normalize/Level Adjust1U Erase Punch Noise Index To execute the Time Stretch command, press the OK but- ton1V Time Stretch Start End1W Transfer Wave Transfer Wave To Midi Track Stereo file1D Copy Track 1E Bounce Track 1C Erase TrackIf executing with Track Select set to a Midi track Track Dialog box when executing Erase Measure 1J Copy Measure 1K Move Measure 1Q Set Song Length Resample SEQ Play Auto Sampling/HD Audio SetupInitialize ResamplePerforming in-track sampling In-Track SamplingListen to the sampled data Resampling a completed song to create a Wave file 2ch Mix to DiskHD Audio Track REC Listen to the Wave file that you createdCheck the audio tracks that you recorded Bounce Audio TrackRecording on the audio tracks Perform bounce-recordingAutomatically-set parameters and their values Parameter Initialize Resample SEQ Play In-Track SamplingDisk Recording and playing exclusive events Support for exclusive eventsRecording internal parameter changes Recording exclusive messages received from the TRITON-Rack Exclusive messages that can be realtime-recordedMidi system exclusive parameter changes Put Effect Setting to Track Effect IFX3Choose Put Effect Setting to Track to open the dialog box Beat.Tick1B Event Edit Sequencer P6 Pattern/RPPR1F Erase Measure 1C Put Effect Setting to Track Added page menu command1D Put Effect Setting to Track Sequencer P8 Insert Effect123456a Tone Adjust 1-Tone Adjust Tone Adjust ParametersDestination and Value LFO1 P Int LFO1 Pitch Intensity -12.00...+00.00...+12.00 LFO1 Dly LFO1 Delay 99...+00...+99LFO1 Spd LFO1 Speed 199...+00...+199 LFO1 Fade 99...+00...+991L Copy From Program Copy From ProgramSwing Quantize Parameter 1N Quantize Swing 300%...+300%Compare function Auto Song Setup functionOther updates ImprovementsDisk mode Edit Wave6b Wave Parameter 6E Copy 6K Volume Ramp6D Clear 6F InsertAdvanced Conversion Load Load Akai Program File Load Akai VolumeLoad Akai Program File Load PCG RAM and Samples 1D Load PCG RAM and SamplesLoad Standard Midi File Content that will be loaded from the .PCG fileContent loaded from the .SNG file Exclusive Off, OnOptimize Medium Save Song as Standard Midi File3J Optimize Medium Create a directory on the copy-destination media Collect Audio Track file3K Collect Audio Track file Collect the song file and Wave file into a single directoryGlobal Loading Karma Music Workstation or Triton Le .PCG SNG files Global mode parametersRate Convert Karma functionData compatibility Scsi Mode Target Global modeScsi Mode Initiator, Target Scsi Mode/SCSI IDFoot Switch Assign Scsi Mode Initiator1O Auto Sampling Setup Sampling modeAuto Sampling Setup REC Audio InputCheck the resampled data Auto Resample through IFXSampling Use the radio buttons to select Auto Resample through IFXIFX Copying data from a Wave file, and inserting it in a sample Menu commands Insert Mix, PasteFrom, select Disk Page Resample Combination Play Combination mode5E Auto Sampling Setup Use the radio buttons to select Resample Combination PlayStart playing the combination that uses the arpeggiator etc Source Audio*2 Input1 Level 127 Pan L000 BUS Select 1C Copy From Program 3E Auto Sampling Setup Program modeResample Program Play Start playing the program that uses the arpeggiator etc Initialize Resample Program Play REC Audio Input Various messages Other functionalityTap tempo control Changed messagesAdded messages Korg INC
Top Page Image Contents