Korg V2 manual Sampling/HD Audio, 7a Input COMBI, PROG, SEQ, S.PLAY, Disk, 7b Ctrl Control

0–7: Sampling/HD Audio

The 0–7: Sampling page has changed to the 0–7: Sampling/ HD Audio page (the tab has changed from Sampling to Sampling/HD Audio), and audio track playback parameters and page menu commands have been added.

0–7

0–7a

0–7b 0–7c

0–7a: Input (COMBI, PROG, SEQ, S.PLAY, DISK)

Here you can select input sources such as analog/digital audio devices and instruments, and set the input level, pan, bus, and master effect send. (☞PG p.139 “Global 0–3a: Input (COMBI, PROG, SEQ, S.PLAY, DISK)”)

0–7b: Ctrl (Control)

A “Ctrl” parameter has been added above “Recording Level [dB]” (0–7c ☞PG p.56). “Ctrl” lets you choose whether to adjust the settings for sampling setup or for audio track out- put. The screen display will depend on the parameter you select.

Ctrl (Control) [Sampling Setup, Audio Track]

Selects which parameters will be accessible.

Sampling Setup: Sampling setup parameters. This is the same as on previous versions. (0–7b ☞PG p.56)

Audio Track: Output settings for the audio tracks.

3 4

1 “Pan” 1

2“Level”

3 “BUS(IFX/Indiv.) Select”

4“S1, S2”

5	“PLAY/MUTE/REC”	2
6	“SOLO ON/OFF ”
		5	6
Pan			[L000...C064...R127]

Specifies the panning of the audio track output.

Level [0...127]

Specifies the output level of the audio track.

BUS (IFX/Indiv.) Select	[L/R, IFX1...5, 1...4,
	1/2, 3/4, Off]

Selects the bus for the audio track.

L/R: The output of the audio track will be sent to the OUT- PUT MAIN L (MONO)/R jacks.

IFX1...IFX5: The output of the audio track will be sent to an insert effect. To specify the output routing from the insert effect, use Sequencer P8: Insert Effect, Insert FX page “BUS Sel. (BUS Select)” (☞PG p.84).

1...4: The output of the audio track will be sent to the OUT- PUT (INDIVIDUAL) 1...4 jack.

1/2, 3/4: The output of the audio track will be sent to the OUTPUT (INDIVIDUAL) 1/2 jacks or 3/4 jacks.

Off: The output of the audio track will not be sent to a bus. Use this setting if you want to send the audio track output only to a master effect. To adjust the send level to the master effect, use “S1 (Send 1 to MFX1)” or “S2 (Send 2 to MFX2).”

S1 (Send 1 to MFX1), S2 (Send 2 to MFX2) [000...127]

Adjusts the send level from the audio track output to each of the master effects. These settings can be used only if “BUS (IFX/Indiv.) Select” is set to L/R or Off. If “BUS (IFX/Indiv.) Select” is set to IFX1–5, you can adjust the send level to the master effects by using “Send 1” and “Send 2” that follow IFX1–5(8–1b☞PG p.84).

PLAY/MUTE/REC [PLAY, MUTE, REC, P/R]

This display lets you set the record and play back status of each audio track.

This setting will change each time you press the PLAY/ MUTE/REC button.

The status of each track may be set independently. PLAY: The track will play back.

MUTE: The track will be muted.

REC: This will be displayed when you record. It cannot be selected.

P/R: This will be displayed when you perform bounce- recording (☞p.12, 18). It cannot be selected.

SOLO ON/OFF [Off, On]

Switches the solo function on/off.

Only tracks whose SOLO is ON will play back. Other tracks (including MIDI tracks) will be muted.

The setting will alternate each time you press the SOLO ON/OFF button.

If the page menu command “Solo Selected Track” (0– 1B) is on, that solo setting will take priority. If you press “SOLO ON/OFF” or a parameter of another track, only that track will be soloed and will play back.

The “Pan,” “Level,” “S1,” and “S2” parameters of Audio Tracks 1 and 2 cannot be controlled by transmit- ting/receiving or recording MIDI control change mes- sages. However these parameters can be controlled by recording/playing exclusive events. (☞p.34)

0–7c: Recording Level [dB]

This adjusts the signal level at the final stage of recording. (☞PG p.92 “Sampling 0–1d: Recording Level [dB]”)

Sequencer

15