Korg V2 manual Added messages

Page 76

Added messages

The following messages have been added.

Audio Track size over limit

Meaning: Recording or editing an audio track in Sequencer mode has caused the audio track to exceed its maximum length of 80 minutes.

Action: You cannot record or edit an audio track so that it would exceed 80 minutes.

Can’t record Audio Track

Change MIDI Clock to Internal

Meaning: You attempted to record an audio track when “MIDI Clock” (☞PG p.143) was set to other than Internal. To play back or record an audio track, the “MIDI Clock” must be set to Internal.

Action: In Global mode, set “MIDI Clock” (☞PG p.143) to Internal.

Exceeded 8 Programs

Meaning: During execution of Advanced Conversion Load, the maximum number of eight programs was exceeded. Depending on the structure of the AKAI Program, it may be convert-loaded as mul- tiple programs and one combination. In this case, the number of TRITON programs resulting from the conversion is limited to the maximum number of programs that can used in a combination (i.e., eight programs).

Action: After loading one AKAI Program, edit it on the

TRITON.

Action: Instead of using Advanced Conversion Load, load the data as multisamples or samples, and then edit it on the TRITON.

File/path not found

Meaning: When you attempted to play or record an audio track, the WAVE file assigned to the audio track of the song did not exist in the save-destination directory.

Action: Use the Sequencer P0: Play/REC, Sampling/HD Audio page menu command “Sel Dir/WAVE (Audio Track)” to reassign the appropriate WAVE file.

Meaning: When you attempted to execute the Disk mode page menu command “Collect Audio Track file,” the WAVE file assigned to the audio track of the song file did not exist in the save-destination directory.

Action: Use the Sequencer P0: Play/REC, Sampling/HD Audio page menu command “Sel Dir/WAVE (Audio Track)” to reassign the appropriate WAVE file, and then use the Disk 0-2: Save page menu command “Save SEQ” to save.

Source file is not 44100 Hz or 48000 Hz

Can’t put

Meaning: When executing the Sequencer mode P5: Track Edit page menu command “Put WAVE,” you had selected a WAVE file that was other than 44.1 kHz or 48 kHz.

Action: WAVE files other than 44.1 kHz or 48 kHz cannot be placed in an audio track.

Source file is not 44100 Hz or 48000 Hz

Can’t set

Meaning: When executing the Sequencer mode P0: Play/ REC, Sampling/HD Audio page menu command “Sel Dir/WAVE (Audio Track),” you had selected a WAVE file that was other than 44.1 kHz or 48 kHz.

Action: WAVE files other than 44.1 kHz or 48 kHz cannot be assigned to an audio track.

There is no WAVE file to copy

Meaning: When executing the page menu command “Col- lect Audio Track file,” the WAVE file to be copied for that song file did not exist. (All WAVE files used by the audio track were found in the speci- fied directory.)

Action: Verify that a WAVE file has been assigned to the audio track of the song, and once again use the Sequencer mode P0: Play/REC, Sampling/HD Audio page menu command “Sel Dir/WAV (Audio Track)” to reassign the WAVE file to the audio track.

Do not move the WAVE file used by the audio track to a different directory. The audio track cannot be played if you do so. If you do move the WAVE file, you must once again use the Sequencer mode P0: Play/REC, Sampling/HD Audio page menu command “Sel Dir/ WAVE (Audio Track)” to reassign the WAVE file to the audio track.

This file does not have an Audio Tracks

Meaning: An audio track does not exist for the song file on which you attempted to execute the page menu command “Collect Audio Track.”

Action: Make sure that the song file was created by the TRITON STUDIO version 2.0.

WAVE file size over limit

Meaning: When using Disk mode Edit WAVE to edit, you exceeded the maximum allowable length of 230,400,000 samples (80 minutes at a sampling rate of 48 kHz) for a WAVE file.

Action: You cannot use Edit WAVE to edit a WAVE file that exceeds 230,400,000 samples (80 minutes at a sampling rate of 48 kHz).

Add these messages to Parameter Guide – 9. Appendices – Various messages (☞PG p.272).

Disk

Global

Other functionality Program Combination Sampling

71

Page 75 Page 77
Image 76
Page 75 Page 77
Contents Update guide Table of Contents Global mode Sampling modeCombination mode Program modeHow this manual is organized About this manualConventions in this manual Page Introduction Sequencer modeNew functions in version Other new functions Installing the system Updating the Triton Studio operating systemPage HD Audio Recording Sequencer modeAbout the HD Audio Track function About the audio tracks Audio Track 1&2 Erase Measure Specify the location where the Wave file will be saved Recording an audio trackPreparing to record an audio track Create a directory in which to save the filesRecord the audio track SetupConnect your guitar Record Set the recording levelPress the Sequencer REC/WRITE key Using punch-in recording Check the recorded contentPunch In checked Punch In Mode Auto Press the Sequencer START/STOP key to stop recordingCompare the recorded content Performing bounce recordingWhen you have finished setting your levels, stop play- back Menu commands Sequencer P0 Play/RECTrack Select 1D Delete SongSampling/HD Audio 7a Input COMBI, PROG, SEQ, S.PLAY, Disk7b Ctrl Control 7c Recording Level dBAuditioning the contents of a Wave file Menu Command7B Sel Dir/WAVE Audio Track 7C Auto Sampling/HD Audio Setup 7D Bounce All Tracks To SongPunch In Mode Manual, Auto PreferencePunch Off, On Bounce Off, OnChanges to the page menu commands Sequencer P1 Cue ListNew page menu commands Sequencer P5 Track EditTrack and Map 1R Put Wave1T Volume Ramp 1S Normalize/Level Normalize/Level Adjust1U Erase Punch Noise To execute the Time Stretch command, press the OK but- ton 1V Time StretchIndex Start End1W Transfer Wave Transfer Wave To Midi Track Stereo file1D Copy Track 1E Bounce Track 1C Erase TrackIf executing with Track Select set to a Midi track Track Dialog box when executing Erase Measure 1J Copy Measure 1K Move Measure 1Q Set Song Length Auto Sampling/HD Audio Setup InitializeResample SEQ Play ResamplePerforming in-track sampling In-Track SamplingListen to the sampled data 2ch Mix to Disk HD Audio Track RECResampling a completed song to create a Wave file Listen to the Wave file that you createdBounce Audio Track Recording on the audio tracksCheck the audio tracks that you recorded Perform bounce-recordingAutomatically-set parameters and their values Parameter Initialize Resample SEQ Play In-Track SamplingDisk Recording and playing exclusive events Support for exclusive eventsRecording internal parameter changes Recording exclusive messages received from the TRITON-Rack Exclusive messages that can be realtime-recordedMidi system exclusive parameter changes Put Effect Setting to Track Effect IFX3Choose Put Effect Setting to Track to open the dialog box Beat.Tick1B Event Edit Sequencer P6 Pattern/RPPR1F Erase Measure Added page menu command 1D Put Effect Setting to Track1C Put Effect Setting to Track Sequencer P8 Insert Effect123456a Tone Adjust 1-Tone Adjust Tone Adjust ParametersDestination and Value LFO1 Dly LFO1 Delay 99...+00...+99 LFO1 Spd LFO1 Speed 199...+00...+199LFO1 P Int LFO1 Pitch Intensity -12.00...+00.00...+12.00 LFO1 Fade 99...+00...+99Copy From Program Swing Quantize Parameter1L Copy From Program 1N Quantize Swing 300%...+300%Auto Song Setup function Other updatesCompare function ImprovementsDisk mode Edit Wave6b Wave Parameter 6K Volume Ramp 6D Clear6E Copy 6F InsertAdvanced Conversion Load Load Akai Program File Load Akai VolumeLoad Akai Program File Load PCG RAM and Samples 1D Load PCG RAM and SamplesContent that will be loaded from the .PCG file Content loaded from the .SNG fileLoad Standard Midi File Exclusive Off, OnOptimize Medium Save Song as Standard Midi File3J Optimize Medium Collect Audio Track file 3K Collect Audio Track fileCreate a directory on the copy-destination media Collect the song file and Wave file into a single directoryGlobal Global mode parameters Rate ConvertLoading Karma Music Workstation or Triton Le .PCG SNG files Karma functionData compatibility Global mode Scsi Mode Initiator, TargetScsi Mode Target Scsi Mode/SCSI IDFoot Switch Assign Scsi Mode InitiatorSampling mode Auto Sampling Setup1O Auto Sampling Setup REC Audio InputAuto Resample through IFX SamplingCheck the resampled data Use the radio buttons to select Auto Resample through IFXIFX Copying data from a Wave file, and inserting it in a sample Menu commands Insert Mix, PasteFrom, select Disk Page Combination mode 5E Auto Sampling SetupResample Combination Play Use the radio buttons to select Resample Combination PlayStart playing the combination that uses the arpeggiator etc Source Audio*2 Input1 Level 127 Pan L000 BUS Select 1C Copy From Program 3E Auto Sampling Setup Program modeResample Program Play Start playing the program that uses the arpeggiator etc Initialize Resample Program Play REC Audio Input Other functionality Tap tempo controlVarious messages Changed messagesAdded messages Korg INC
Top Page Image Contents