Invacare 9000 XT, 9000XT Recliner, 9000 Series, 9000 XDT XDT and 9000 SL, Mounting Screws

Page 24

SECTION 3—SEAT AND BACK

9000 XDT and 9000 SL

NOTE: For this procedure, refer to FIGURE 3.6.

NOTE: 9000 XDT wheelchairs have two (2)

frame depth ranges: 16 to 18 inches and 19 to 20 inches. A 16‐18‐inch frame depth wheelchair cannot be adjusted to a 19 to 20‐inch range and vice‐versa.

1.Remove the existing seat upholstery from the wheelchair. Refer to Replacing the Seat Upholstery in the Owner’s Manual, part number 1056953.

NOTE: When adjusting the seat depth of the wheelchair, the seat upholstery MUST also be changed.

2.Remove the two (2) plug buttons from the ends of the crossbraces that are towards the front of the wheelchair.

NOTE: The two (2) plug buttons are used in the ends of the seat extension tubes.

3.Install the two (2) seat extension tubes into the ends on the crossbraces.

4.Perform one (1) of the following:

•9000 XDT ‐ Align the second mounting hole from the rear of the seat extension tube with the frontmost mounting hole in the crossbrace.

9000 XDT

	Mounting Screws	Rear of
	Mounting Screws	Seat
		Seat

Washer

Seat Upholstery

Seat

Extension

Tube

Front of			Crossbrace
Front of		DO NOT use
Seat		DO NOT use
Seat			this back
			this back
	Second	mounting hole
Plug Button	Mounting
Plug Button	Hole
	Hole
	9000 SL		Rear of
			Rear of
Mounting Screws			Seat
Seat Upholstery
Seat Extension			Crossbrace
Tube			Crossbrace
Tube
Spacer
Tube			Second
			Second
			Mounting
Front of			Hole
Seat			Rear
	Spacer Tube		Mounting

Mounting Hole	Hole

NOTE: DO NOT use back mounting hole. If back mounting hole is used, the mounting hole for the other mounting screw will not line up properly.

Plug Button

FIGURE 3.6 Adjusting Seat Depth - 9000

XDT and 9000 SL

•9000 SL ‐ Align the rear mounting hole of the seat extension tube with the second mounting hole from the front of the crossbrace. Slide spacer tube over seat extension tube.

NOTE: The rear mounting hole is further from its end of the seat extension tube than the front mounting hole is from its end.

NOTE: The end of the spacer tube that is closer to the spacer tube mounting hole should face to the front.

5. Repeat STEP 4 for the opposite seat extension tube.

9000 Series

24

Part No. 1076155

Image 24

Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Special Notes Wheelchair TIE-DOWN Restraints and Seat RestraintsLabel Location Important NoticeTypical Product Parameters 9000 SL9000 XT Typical Product Parameters XT Recliner 9000 XDT General Guidelines Stability All ModelsAnti-Tippers Operating InformationStability Recliner Models Only Weight Training Weight LimitationTire Pressure Safety INSPECTION/TROUBLESHOOTING ChecklistTroubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Adjusting Back Angle Seat and BackAdjusting Back Height SL without Adjustable Back Angle OptionAdjusting Seat Width SL with Adjustable Back Angle Option and 9000 XT/XDTPivot Link Adjusting Seat Width Adjusting Seat Depth 9000XT ModelXDT and 9000 SL Mounting ScrewsSeat and Back Front Caster Mounting Adjustments Front CastersWheelchair Frame Repositioning/Replacing Cam Seat to Floor Changing Seat-to-Floor Height/Seat-to-Floor AngleAngle ‐ a 3 seat‐to‐floor angle is the only available angle Super Low Frame Style Adult/Tall Frame StyleAdult/Hemi Frame Styles AngleForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Removing/Installing Rear Wheels Rear WheelsQuick-Release Axles Permanent Axles Detent PinModels with Offset Axle Option Rear Wheels Spacers Adjusting Quick-Release Axle Adjusting Wheelbase LengthRecliner Replacing Release HandleAdjusting Cable Assembly Tension Replacing Release HandleReplacing Cable Assembly Adjusting Cable Assembly TensionDisconnecting/Connecting Lower Cable Assembly DisconnectingConnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Locking Rod Replacing Back TubeRecliner Removing/Installing Spring Lift Mechanism RemovingInstalling Removing/Installing Spring Lift MechanismReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth Using/Adjusting Wheel Locks Using Attendant Operated Wheel LocksWith Patient Operated Wheel Locks With Attendant Operated Wheel LocksAdjusting Attendant Operated Wheel Locks 14 Using Attendant Operated Wheel Locks15 Adjusting Attendant Operated Wheel Locks Changing Seat-to-Floor HeightInstalling Anti-Tippers 16 Changing Seat-to-Floor HeightRecliner XT Recliner Installing/Adjusting Anti-tippers Installing Anti-TippersANTI-TIPPERS/WHEEL Locks Adjusting Anti-Tippers Installing Anti-TippersUsing/Adjusting Disk Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico

Related manuals

Manual 30 pages 6.48 Kb

Manual 60 pages 56.17 Kb