Invacare 9000 Series, 9000 XT, 9000 XDT Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle

Page 47

SECTION 5—SEAT TO FLOOR

*NOTE: The seat‐to‐floor heights are based on urethane tires. If wheelchair is equipped with pneumatic (properly inflated) or solid rubber tires, add ¼ inch to the measurements listed above. These heights can vary +/‐ ¼ inch due to tire wear and manufacturing tolerances.

NOTE: Charts 29 to 31 apply to adult/hemi frame styles only. Refer to the charts for seat‐to‐floor height settings for adult/tall (Adult/Tall Frame Style on page 31) and super low frame styles (Super Low Frame Style on page 31) and Changing Seat‐to‐Floor Height on page 77 for recliner frame styles.

Chart 29 - Seat-to-Floor Height of 18½ inches and 6° Angle

	REAR WHEEL POSITION		ANTI-TIP	FRONT CASTER
	OFFSET AXLE OPTION STANDARD		PART/MODEL	MOUNTING	ADJC CAM
	OFFSET AXLE OPTION STANDARD		NUMBERS	MOUNTING	ADJC CAM
	FORWARD	REARWARD	NUMBERS	POSITION	POSITION
				POSITION	POSITION

	Hole 1	Hole 1	N/A On-Chair		Front
	Hole 1	Hole 1			Front
			1113766 Off-Chair
	Hole 3	Hole 3
					Notch

Chart 30 - Seat-to-Floor Height of 17½ inches and 3° Angle

	REAR WHEEL POSITION		ANTI-TIP	FRONT CASTER
	OFFSET AXLE OPTION STANDARD		PART/MODEL	MOUNTING	ADJC CAM
	OFFSET AXLE OPTION STANDARD		NUMBERS	MOUNTING	ADJC CAM
	FORWARD	REARWARD	NUMBERS	POSITION	POSITION
				POSITION	POSITION

	Hole 1	Hole 1	1360 On-Chair		Front
	Hole 1	Hole 1			Front
			1058836 Off-Chair
	Hole 3	Hole 3
					Notch

Part No. 1076155

47

9000 Series

Image 47

Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Wheelchair TIE-DOWN Restraints and Seat Restraints Special NotesImportant Notice Label Location9000 SL Typical Product Parameters9000 XT Typical Product Parameters XT Recliner 9000 XDT Stability All Models General GuidelinesStability Recliner Models Only Anti-TippersOperating Information Tire Pressure Weight TrainingWeight Limitation Checklist Safety INSPECTION/TROUBLESHOOTINGSuggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety INSPECTION/TROUBLESHOOTING Seat and Back Adjusting Back AngleSL without Adjustable Back Angle Option Adjusting Back HeightSL with Adjustable Back Angle Option and 9000 XT/XDT Adjusting Seat WidthPivot Link Adjusting Seat Width 9000XT Model Adjusting Seat DepthMounting Screws XDT and 9000 SLSeat and Back Front Casters Front Caster Mounting AdjustmentsWheelchair Frame Repositioning/Replacing Cam Changing Seat-to-Floor Height/Seat-to-Floor Angle Seat to FloorAngle ‐ a 3 seat‐to‐floor angle is the only available angle Adult/Tall Frame Style Super Low Frame StyleAngle Adult/Hemi Frame StylesForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Quick-Release Axles Removing/Installing Rear WheelsRear Wheels Detent Pin Permanent AxlesModels with Offset Axle Option Rear Wheels Spacers Adjusting Wheelbase Length Adjusting Quick-Release AxleReplacing Release Handle ReclinerReplacing Release Handle Adjusting Cable Assembly TensionAdjusting Cable Assembly Tension Replacing Cable AssemblyConnecting Disconnecting/Connecting Lower Cable AssemblyDisconnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Back Tube Replacing Locking RodRecliner Removing Removing/Installing Spring Lift MechanismRemoving/Installing Spring Lift Mechanism InstallingReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth With Attendant Operated Wheel Locks Using/Adjusting Wheel LocksUsing Attendant Operated Wheel Locks With Patient Operated Wheel Locks14 Using Attendant Operated Wheel Locks Adjusting Attendant Operated Wheel LocksChanging Seat-to-Floor Height 15 Adjusting Attendant Operated Wheel Locks16 Changing Seat-to-Floor Height Installing Anti-TippersRecliner XT Recliner ANTI-TIPPERS/WHEEL Locks Installing/Adjusting Anti-tippersInstalling Anti-Tippers Installing Anti-Tippers Adjusting Anti-TippersUsing Patient Operated Disk Wheel Locks Using/Adjusting Disk Wheel LocksUsing Patient Operated Disk Wheel Locks Adjusting Patient-Operated Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico

Related manuals

Manual 30 pages 6.48 Kb

Manual 60 pages 56.17 Kb