Invacare 9000 Series, 9000 XT, 9000XT Recliner, 9000 XDT Removing/Installing Spring Lift Mechanism

Page 67

SECTION 7—RECLINER

Spring Grip

Fastener

Back Tube

Back Tube

Mounting Bracket

Swivel Nut

Cable

Assembly

	STEPS 7, 10, 11, 13
Locknut
Locking	Mounting
Rod	Screw

Back Tube

Mounting Back Tube

Bracket

Clevis

Bracket

Mounting Screw

Locknut

FIGURE 7.7 Replacing Back Tube

Removing/Installing Spring Lift Mechanism

NOTE: For this procedure, refer to FIGURE 7.8.

Removing

1.Recline the wheelchair exposing the two (2) holes on either side of the spring lift mechanism.

NOTE: Before removing the spring lift mechanism, a retaining clip must be installed to prevent the spring lift mechanism from compressing. The retaining clip, part number 1021688, can be purchased from Invacare at the number listed on the back cover.

2.Position one (1) end of the retainer clip in each of the holes.

3.Return chair to upright position until top portion of lift mechanism rests on the retaining clip.

4.Remove the locknut that secures the top of the spring lift mechanism to the wheelchair frame.

5.Remove the mounting screw, spacer, and locknut that secures the bottom of the spring lift mechanism to the wheelchair frame.

6.Remove existing spring lift mechanism.

Part No. 1076155

67

9000 Series

Image 67

Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Wheelchair TIE-DOWN Restraints and Seat Restraints Special NotesImportant Notice Label Location9000 SL Typical Product Parameters9000 XT Typical Product Parameters XT Recliner 9000 XDT Stability All Models General GuidelinesOperating Information Anti-TippersStability Recliner Models Only Weight Limitation Weight TrainingTire Pressure Checklist Safety INSPECTION/TROUBLESHOOTINGSuggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety INSPECTION/TROUBLESHOOTING Seat and Back Adjusting Back AngleSL without Adjustable Back Angle Option Adjusting Back HeightSL with Adjustable Back Angle Option and 9000 XT/XDT Adjusting Seat WidthPivot Link Adjusting Seat Width 9000XT Model Adjusting Seat DepthMounting Screws XDT and 9000 SLSeat and Back Front Casters Front Caster Mounting AdjustmentsWheelchair Frame Repositioning/Replacing Cam Changing Seat-to-Floor Height/Seat-to-Floor Angle Seat to FloorAngle ‐ a 3 seat‐to‐floor angle is the only available angle Adult/Tall Frame Style Super Low Frame StyleAngle Adult/Hemi Frame StylesForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Rear Wheels Removing/Installing Rear WheelsQuick-Release Axles Detent Pin Permanent AxlesModels with Offset Axle Option Rear Wheels Spacers Adjusting Wheelbase Length Adjusting Quick-Release AxleReplacing Release Handle ReclinerReplacing Release Handle Adjusting Cable Assembly TensionAdjusting Cable Assembly Tension Replacing Cable AssemblyDisconnecting Disconnecting/Connecting Lower Cable AssemblyConnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Back Tube Replacing Locking RodRecliner Removing Removing/Installing Spring Lift MechanismRemoving/Installing Spring Lift Mechanism InstallingReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth With Attendant Operated Wheel Locks Using/Adjusting Wheel LocksUsing Attendant Operated Wheel Locks With Patient Operated Wheel Locks14 Using Attendant Operated Wheel Locks Adjusting Attendant Operated Wheel LocksChanging Seat-to-Floor Height 15 Adjusting Attendant Operated Wheel Locks16 Changing Seat-to-Floor Height Installing Anti-TippersRecliner XT Recliner Installing Anti-Tippers Installing/Adjusting Anti-tippersANTI-TIPPERS/WHEEL Locks Installing Anti-Tippers Adjusting Anti-TippersUsing Patient Operated Disk Wheel Locks Using/Adjusting Disk Wheel LocksUsing Patient Operated Disk Wheel Locks Adjusting Patient-Operated Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico

Related manuals

Manual 30 pages 6.48 Kb

Manual 60 pages 56.17 Kb