Invacare 9000 SL, 9000 XT, 9000XT Recliner, 9000 Series, 9000 XDT service manual Adjusting Seat Depth

Page 74

SECTION 7—RECLINER

Adjusting Seat Depth

NOTE: For this procedure, refer to FIGURE 7.11.

1.Remove the existing seat upholstery from the crossbraces. Refer to Replacing the Seat Upholstery in the Owner’s Manual, part number 1056953.

	Mounting	Seat
		Upholstery
	Screws

NOTE: When adjusting the seat depth of the wheelchair, the seat upholstery MUST be changed as well.

2.Remove the two (2) plug buttons from the ends of the crossbraces that are towards the front of the wheelchair.

NOTE: DO NOT use back mounting hole shown in FIGURE 7.11. If back mounting hole is used, the mounting hole for the other mounting screw will not line up properly.

3.Install the two (2) seat extension tubes into the ends on the crossbraces.

4.Line up the second mounting hole from the rear of the seat extension tube with the mounting hole in the crossbrace.

Repeat for opposite seat extension tube.

Washer

Seat

Extension

Tube

Crossbrace

		DO NOT use
		this back
	Second	mounting hole
	Second
	Mounting
Plug Button	Hole
Plug Button

NOTE: This illustration depicts the 1‐inch seat extension. The 2‐inch seat extension attaches in the same manner.

FIGURE 7.11 Adjusting Seat Depth

5.Install the new seat upholstery onto the wheelchair. Make sure to line up the mounting holes in the seat extension tubes with the new seat upholstery. Refer to Replacing the Seat Upholstery in the Owner’s Manual, part number 1056953.

6.Install plug buttons into the ends of the seat extension tubes.

9000 Series

74

Part No. 1076155

Image 74

Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Special Notes Wheelchair TIE-DOWN Restraints and Seat RestraintsLabel Location Important NoticeTypical Product Parameters 9000 SL9000 XT Typical Product Parameters XT Recliner 9000 XDT General Guidelines Stability All ModelsStability Recliner Models Only Anti-TippersOperating Information Tire Pressure Weight TrainingWeight Limitation Safety INSPECTION/TROUBLESHOOTING ChecklistMaintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Adjusting Back Angle Seat and BackAdjusting Back Height SL without Adjustable Back Angle OptionAdjusting Seat Width SL with Adjustable Back Angle Option and 9000 XT/XDTPivot Link Adjusting Seat Width Adjusting Seat Depth 9000XT ModelXDT and 9000 SL Mounting ScrewsSeat and Back Front Caster Mounting Adjustments Front CastersWheelchair Frame Repositioning/Replacing Cam Seat to Floor Changing Seat-to-Floor Height/Seat-to-Floor AngleAngle ‐ a 3 seat‐to‐floor angle is the only available angle Super Low Frame Style Adult/Tall Frame StyleAdult/Hemi Frame Styles AngleForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Quick-Release Axles Removing/Installing Rear WheelsRear Wheels Permanent Axles Detent PinModels with Offset Axle Option Rear Wheels Spacers Adjusting Quick-Release Axle Adjusting Wheelbase LengthRecliner Replacing Release HandleAdjusting Cable Assembly Tension Replacing Release HandleReplacing Cable Assembly Adjusting Cable Assembly TensionConnecting Disconnecting/Connecting Lower Cable AssemblyDisconnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Locking Rod Replacing Back TubeRecliner Removing/Installing Spring Lift Mechanism RemovingInstalling Removing/Installing Spring Lift MechanismReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth With Patient Operated Wheel Locks Using/Adjusting Wheel LocksUsing Attendant Operated Wheel Locks With Attendant Operated Wheel LocksAdjusting Attendant Operated Wheel Locks 14 Using Attendant Operated Wheel Locks15 Adjusting Attendant Operated Wheel Locks Changing Seat-to-Floor HeightInstalling Anti-Tippers 16 Changing Seat-to-Floor HeightRecliner XT Recliner ANTI-TIPPERS/WHEEL Locks Installing/Adjusting Anti-tippersInstalling Anti-Tippers Adjusting Anti-Tippers Installing Anti-TippersUsing/Adjusting Disk Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico

Related manuals

Manual 30 pages 6.48 Kb

Manual 60 pages 56.17 Kb