Invacare 9000 XDT, 9000 XT, 9000 Series Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle

Page 43

SECTION 5—SEAT TO FLOOR

Chart 20 - Seat-to-Floor Height of 17½ inches and 6° Angle

REAR WHEEL POSITION

ANTI-TIP

FRONT CASTER

OFFSET AXLE OPTION

STANDARD

PART/MODEL

MOUNTING

ADJC CAM

FORWARD*

REARWARD

 

NUMBERS

POSITION

POSITION

 

 

 

 

 

 

Hole 4

Hole 4

 

N/A On-Chair

 

Front

 

 

 

 

 

 

1113766

 

 

 

 

 

Off-Chair

 

 

Hole 3

Hole 3

 

 

 

Notch

 

 

 

 

*NOTE: This offset axle plate position requires the caster headtube to be leading to provide adequate tire clearance between the rear tire and the front caster. Refer to Converting from Trailing to Leading or Leading to Trailing Casters on page 27.

22-Inch Rear Wheels and 6-Inch Front Casters

WARNING

If changing the seat-to-floor angle to 6°, anti-tippers MUST be installed.

Refer to the following table to determine the obtainable seat‐to‐floor heights and seat‐to‐floor angles for 22‐inch rear wheels and 6‐inch front casters:

SEAT-TO-FLOOR

SEAT-TO-FLOOR

REFER TO

HEIGHT*

ANGLE

 

 

 

 

17½ inches

0°

Chart 21

 

 

 

17½ inches

3°

Chart 22

 

 

 

17½ inches

6°

Chart 23

 

 

 

16½ inches

0°

Chart 24

 

 

 

16½ inches

3°

Chart 25

 

 

 

16½ inches

6°

Chart 26

 

 

 

15½ inches

0°

Chart 27

 

 

 

15½ inches

3°

Chart 28

 

 

 

*NOTE: The seat‐to‐floor heights are based on urethane tires. If wheelchair is equipped with pneumatic (properly inflated) or solid rubber tires, add ¼ inch to the measurements listed above. These heights can vary +/‐ ¼ inch due to tire wear and manufacturing tolerances.

NOTE: Charts 21 to 28 apply to adult/hemi frame styles only. Refer to the charts for seat‐to‐floor height settings for adult/tall (Adult/Tall Frame Style on page 31) and super low frame styles (Super Low Frame Style on page 31) and Changing Seat‐to‐Floor Height on page 77 for recliner frame styles.

Part No. 1076155

43

9000 Series

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Wheelchair TIE-DOWN Restraints and Seat Restraints Special NotesImportant Notice Label Location9000 SL Typical Product Parameters9000 XT Typical Product Parameters XT Recliner 9000 XDT Stability All Models General GuidelinesOperating Information Anti-TippersStability Recliner Models Only Weight Limitation Weight TrainingTire Pressure Checklist Safety INSPECTION/TROUBLESHOOTINGSuggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety INSPECTION/TROUBLESHOOTING Seat and Back Adjusting Back AngleSL without Adjustable Back Angle Option Adjusting Back HeightSL with Adjustable Back Angle Option and 9000 XT/XDT Adjusting Seat WidthPivot Link Adjusting Seat Width 9000XT Model Adjusting Seat DepthMounting Screws XDT and 9000 SLSeat and Back Front Casters Front Caster Mounting AdjustmentsWheelchair Frame Repositioning/Replacing Cam Changing Seat-to-Floor Height/Seat-to-Floor Angle Seat to FloorAngle ‐ a 3 seat‐to‐floor angle is the only available angle Adult/Tall Frame Style Super Low Frame StyleAngle Adult/Hemi Frame StylesForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Rear Wheels Removing/Installing Rear WheelsQuick-Release Axles Detent Pin Permanent AxlesModels with Offset Axle Option Rear Wheels Spacers Adjusting Wheelbase Length Adjusting Quick-Release AxleReplacing Release Handle ReclinerReplacing Release Handle Adjusting Cable Assembly TensionAdjusting Cable Assembly Tension Replacing Cable AssemblyDisconnecting Disconnecting/Connecting Lower Cable AssemblyConnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Back Tube Replacing Locking RodRecliner Removing Removing/Installing Spring Lift MechanismRemoving/Installing Spring Lift Mechanism InstallingReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth With Attendant Operated Wheel Locks Using/Adjusting Wheel LocksUsing Attendant Operated Wheel Locks With Patient Operated Wheel Locks14 Using Attendant Operated Wheel Locks Adjusting Attendant Operated Wheel LocksChanging Seat-to-Floor Height 15 Adjusting Attendant Operated Wheel Locks16 Changing Seat-to-Floor Height Installing Anti-TippersRecliner XT Recliner Installing Anti-Tippers Installing/Adjusting Anti-tippersANTI-TIPPERS/WHEEL Locks Installing Anti-Tippers Adjusting Anti-TippersUsing Patient Operated Disk Wheel Locks Using/Adjusting Disk Wheel LocksUsing Patient Operated Disk Wheel Locks Adjusting Patient-Operated Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico
Related manuals
Manual 30 pages 6.48 Kb Manual 60 pages 56.17 Kb
Top Page Image Contents