Invacare 9000XT Recliner, 9000 XT, 9000 Series, 9000 XDT, 9000 SL service manual Adjusting Seat Width

Page 71

SECTION 7—RECLINER

Adjusting Seat Width

NOTE: For this procedure, refer to FIGURE 7.10 on page 73.

NOTE: When adjusting the seat width of the wheelchair, the back and seat upholstery, and spreader bar MUST be changed. If applicable, the headrest pillow and headrest upholstery MUST be changed as well.

1.If applicable, remove the headrest pillow. Refer to Replacing the Headrest Pillow in the ownerʹs manual, part number 1056953.

2.If applicable, remove the headrest upholstery. Refer to Replacing the Headrest/Back Upholstery in the ownerʹs manual, part number 1056953.

3.Remove the spreader bar. Refer to Storing/Replacing the Spreader Bar in the ownerʹs manual, part number 1056953.

4.Remove the existing back and seat upholstery from the wheelchair. Refer to Replacing the Headrest/Back Upholstery and Replacing the Seat Upholstery in the ownerʹs manual, part number 1056953.

5.Remove the button screws and locknuts that secure the two (2) pivot links to the wheelchair frame and crossbraces.

6.Remove the two (2) button screws, locknuts and crossbrace saddle that secures the bottom of the crossbrace to the wheelchair frame. Repeat for other crossbrace.

7.Remove the hex screw, coved washers, washers and locknut that secure the two (2) crossbraces together. See Detail ʺBʺ of FIGURE 7.10.

NOTE: Make note of the orientation of the coved washers, washers and locknut for assembling the new crossbraces. See Detail ʺBʺ of FIGURE 7.10.

8.Assemble the two (2) new crossbraces with the existing hex screw, coved washers, washers and locknut. Securely tighten. Refer to Detail ʺBʺ of FIGURE 7.10 for hardware orientation.

9.Determine the correct pivot link and mounting hole to use with the desired seat width. Refer to the following chart.

Part No. 1076155

71

9000 Series

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Wheelchair TIE-DOWN Restraints and Seat Restraints Special NotesImportant Notice Label Location9000 SL Typical Product Parameters9000 XT Typical Product Parameters XT Recliner 9000 XDT Stability All Models General GuidelinesStability Recliner Models Only Anti-TippersOperating Information Tire Pressure Weight TrainingWeight Limitation Checklist Safety INSPECTION/TROUBLESHOOTINGSuggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety INSPECTION/TROUBLESHOOTING Seat and Back Adjusting Back AngleSL without Adjustable Back Angle Option Adjusting Back HeightSL with Adjustable Back Angle Option and 9000 XT/XDT Adjusting Seat WidthPivot Link Adjusting Seat Width 9000XT Model Adjusting Seat DepthMounting Screws XDT and 9000 SLSeat and Back Front Casters Front Caster Mounting AdjustmentsWheelchair Frame Repositioning/Replacing Cam Changing Seat-to-Floor Height/Seat-to-Floor Angle Seat to FloorAngle ‐ a 3 seat‐to‐floor angle is the only available angle Adult/Tall Frame Style Super Low Frame StyleAngle Adult/Hemi Frame StylesForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Quick-Release Axles Removing/Installing Rear WheelsRear Wheels Detent Pin Permanent AxlesModels with Offset Axle Option Rear Wheels Spacers Adjusting Wheelbase Length Adjusting Quick-Release AxleReplacing Release Handle ReclinerReplacing Release Handle Adjusting Cable Assembly TensionAdjusting Cable Assembly Tension Replacing Cable AssemblyConnecting Disconnecting/Connecting Lower Cable AssemblyDisconnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Back Tube Replacing Locking RodRecliner Removing Removing/Installing Spring Lift MechanismRemoving/Installing Spring Lift Mechanism InstallingReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth With Attendant Operated Wheel Locks Using/Adjusting Wheel LocksUsing Attendant Operated Wheel Locks With Patient Operated Wheel Locks14 Using Attendant Operated Wheel Locks Adjusting Attendant Operated Wheel LocksChanging Seat-to-Floor Height 15 Adjusting Attendant Operated Wheel Locks16 Changing Seat-to-Floor Height Installing Anti-TippersRecliner XT Recliner ANTI-TIPPERS/WHEEL Locks Installing/Adjusting Anti-tippersInstalling Anti-Tippers Installing Anti-Tippers Adjusting Anti-TippersUsing Patient Operated Disk Wheel Locks Using/Adjusting Disk Wheel LocksUsing Patient Operated Disk Wheel Locks Adjusting Patient-Operated Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico
Related manuals
Manual 30 pages 6.48 Kb Manual 60 pages 56.17 Kb
Top Page Image Contents