Invacare 9000 XDT, 9000 XT Anti-Tippers, Operating Information, Stability Recliner Models Only

Page 13

SECTION 1—GENERAL GUIDELINES

Stability - Recliner Models Only

ALWAYS make sure that the wheelchair is stable before using the recliner option.

Ensure the spreader bar is attached and secured before using the 9000XT Recliner.

ALWAYS return the back to the upright position before lifting the wheelchair.

Lift Kit Models only ‐ Both spring lift mechanisms MUST be operational before using the recliner. DO NOT operate the recliner option if only one (1) of the spring lift mechanisms is operational.

Anti-Tippers

Anti‐tippers are specific to the different seat‐to‐floor angles and/or seat‐to‐floor heights. Refer to the charts in Installing/Adjusting Anti‐tippers on page 80 for correct usage and adjustment. If these requirements cannot be achieved, DO NOT use the wheelchair.

Contact a qualified technician. If changing the seat‐to‐floor height with or without a change to seat‐to‐floor angle, the correct anti‐tippers MUST be used to maintain a 1½ to 2‐inch ground clearance.

Seat‐to‐floor angle of 0° or 3°: If so equipped, anti‐tippers MUST be attached at all times. Inasmuch as the anti‐tippers are an option for 0° or 3° on this wheelchair (you may order with or without the anti‐tippers), Invacare strongly recommends ordering the anti‐tippers as a safeguard for the wheelchair user.

Seat‐to‐floor angle of 6°: If changing the seat‐to‐floor angle to 6°, anti‐tippers MUST be installed.

Operating Information

Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.

Unless otherwise noted, all service and adjustment should be performed while the wheelchair is unoccupied.

When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water. Verify that grips are dry prior to use. Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly. Failure to observe this warning may result in injury to the user or bystanders.

If the wheelchair is exposed to extreme temperature (above 100°F or below 32°F), high humidity and/or becomes wet, ensure prior to use that the handgrips do not twist on the handle. Otherwise, damage or injury may occur.

Avoid storing or using the wheelchair near open flame or combustible products. Serious injury or damage to property may result.

Part No. 1076155

13

9000 Series

Image 13
Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Wheelchair TIE-DOWN Restraints and Seat Restraints Special NotesImportant Notice Label Location9000 SL Typical Product Parameters9000 XT Typical Product Parameters XT Recliner 9000 XDT Stability All Models General GuidelinesOperating Information Anti-TippersStability Recliner Models Only Weight Limitation Weight TrainingTire Pressure Checklist Safety INSPECTION/TROUBLESHOOTINGMaintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Seat and Back Adjusting Back AngleSL without Adjustable Back Angle Option Adjusting Back HeightSL with Adjustable Back Angle Option and 9000 XT/XDT Adjusting Seat WidthPivot Link Adjusting Seat Width 9000XT Model Adjusting Seat DepthMounting Screws XDT and 9000 SLSeat and Back Front Casters Front Caster Mounting AdjustmentsWheelchair Frame Repositioning/Replacing Cam Changing Seat-to-Floor Height/Seat-to-Floor Angle Seat to FloorAngle ‐ a 3 seat‐to‐floor angle is the only available angle Adult/Tall Frame Style Super Low Frame StyleAngle Adult/Hemi Frame StylesForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Rear Wheels Removing/Installing Rear WheelsQuick-Release Axles Detent Pin Permanent AxlesModels with Offset Axle Option Rear Wheels Spacers Adjusting Wheelbase Length Adjusting Quick-Release AxleReplacing Release Handle ReclinerReplacing Release Handle Adjusting Cable Assembly TensionAdjusting Cable Assembly Tension Replacing Cable AssemblyDisconnecting Disconnecting/Connecting Lower Cable AssemblyConnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Back Tube Replacing Locking RodRecliner Removing Removing/Installing Spring Lift MechanismRemoving/Installing Spring Lift Mechanism InstallingReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth Using Attendant Operated Wheel Locks Using/Adjusting Wheel LocksWith Patient Operated Wheel Locks With Attendant Operated Wheel Locks14 Using Attendant Operated Wheel Locks Adjusting Attendant Operated Wheel LocksChanging Seat-to-Floor Height 15 Adjusting Attendant Operated Wheel Locks16 Changing Seat-to-Floor Height Installing Anti-TippersRecliner XT Recliner Installing Anti-Tippers Installing/Adjusting Anti-tippersANTI-TIPPERS/WHEEL Locks Installing Anti-Tippers Adjusting Anti-TippersUsing Patient Operated Disk Wheel Locks Using/Adjusting Disk Wheel LocksUsing Patient Operated Disk Wheel Locks Adjusting Patient-Operated Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico
Related manuals
Manual 30 pages 6.48 Kb Manual 60 pages 56.17 Kb