Invacare 9000 XDT, 9000 XT, 9000XT Recliner, 9000 Series, 9000 SL Permanent Axles, Detent Pin

Page 53

SECTION 6—REAR WHEELS

5.If the detent balls are not protruding past the inside of the axle bushing or there is too much side‐to‐side movement of the rear wheel assembly, refer to the Owner’s Manual (part number 1056953) for instructions on adjusting the quick release axle.

DETAIL “A” - DETENT BALLS AND DETENT PIN

Axle Bushing

Detent Balls

Inside of

Wheelchair

Detent Pin

Outside of

Wheelchair

 

Quick-Release Axle

Axle Mounting Positions

Axle Spacer (Conventional Arms Only)

Quick-Release Axle

Wheelchair Frame

Rear Wheel

FIGURE 6.1 Removing/Installing Rear Wheels - Quick-Release Axles

Permanent Axles

Models without Offset Axle Option

NOTE: For this procedure, refer to FIGURE 6.2.

NOTE: If replacing the same size rear wheel, note the mounting position on the wheelchair frame for proper reinstallation of the new rear wheel.

1.Remove the hub cap (if applicable), mounting screw and locknut that secure the rear wheel and axle spacer (if applicable) to the wheelchair.

NOTE: Axle spacer is used only if wheelchair is equipped with conventional arms.

2.To reinstall the rear wheel onto the wheelchair, reverse STEP 1.

3.Torque locknut to 40‐45 ft‐lbs.

4.Repeat STEPS 1‐3 for the opposite wheel.

Part No. 1076155

53

9000 Series

Image 53
Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Wheelchair TIE-DOWN Restraints and Seat Restraints Special NotesImportant Notice Label Location9000 SL Typical Product Parameters9000 XT Typical Product Parameters XT Recliner 9000 XDT Stability All Models General GuidelinesStability Recliner Models Only Anti-TippersOperating Information Tire Pressure Weight TrainingWeight Limitation Checklist Safety INSPECTION/TROUBLESHOOTINGMaintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Seat and Back Adjusting Back AngleSL without Adjustable Back Angle Option Adjusting Back HeightSL with Adjustable Back Angle Option and 9000 XT/XDT Adjusting Seat WidthPivot Link Adjusting Seat Width 9000XT Model Adjusting Seat DepthMounting Screws XDT and 9000 SLSeat and Back Front Casters Front Caster Mounting AdjustmentsWheelchair Frame Repositioning/Replacing Cam Changing Seat-to-Floor Height/Seat-to-Floor Angle Seat to FloorAngle ‐ a 3 seat‐to‐floor angle is the only available angle Adult/Tall Frame Style Super Low Frame StyleAngle Adult/Hemi Frame StylesForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Quick-Release Axles Removing/Installing Rear WheelsRear Wheels Detent Pin Permanent AxlesModels with Offset Axle Option Rear Wheels Spacers Adjusting Wheelbase Length Adjusting Quick-Release AxleReplacing Release Handle ReclinerReplacing Release Handle Adjusting Cable Assembly TensionAdjusting Cable Assembly Tension Replacing Cable AssemblyConnecting Disconnecting/Connecting Lower Cable AssemblyDisconnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Back Tube Replacing Locking RodRecliner Removing Removing/Installing Spring Lift MechanismRemoving/Installing Spring Lift Mechanism InstallingReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth Using Attendant Operated Wheel Locks Using/Adjusting Wheel LocksWith Patient Operated Wheel Locks With Attendant Operated Wheel Locks14 Using Attendant Operated Wheel Locks Adjusting Attendant Operated Wheel LocksChanging Seat-to-Floor Height 15 Adjusting Attendant Operated Wheel Locks16 Changing Seat-to-Floor Height Installing Anti-TippersRecliner XT Recliner ANTI-TIPPERS/WHEEL Locks Installing/Adjusting Anti-tippersInstalling Anti-Tippers Installing Anti-Tippers Adjusting Anti-TippersUsing Patient Operated Disk Wheel Locks Using/Adjusting Disk Wheel LocksUsing Patient Operated Disk Wheel Locks Adjusting Patient-Operated Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico
Related manuals
Manual 30 pages 6.48 Kb Manual 60 pages 56.17 Kb