Invacare 9000 XT, 9000XT Recliner ANTI-TIPPERS/WHEEL Locks, Installing/Adjusting Anti-tippers

Page 80

SECTION 8—ANTI-TIPPERS/WHEEL LOCKS

SECTION 8—ANTI-TIPPERS/WHEEL LOCKS

WARNING

After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur.

NOTE: The procedures in this section apply to non‐recliner models only except where noted. For the 9000XT recliner, refer to Recliner on page 58.

Installing/Adjusting Anti-tippers

WARNING

Anti-tippers are specific to the different seat-to-floor angles and/or seat-to-floor heights. Refer to the chart on page 81 for correct usage and adjustment. If these requirements cannot be achieved, DO NOT use the wheelchair. Contact a qualified technician. If changing the seat-to-floor height with or without a change to seat-to-floor angle, the correct anti-tippers MUST be used to maintain a 1-1/2 to 2-inch ground clearance.

Seat-to-floor angle of 0° or 3°: If so equipped, anti-tippers MUST be attached at all times. Inasmuch as the anti-tippers are an option for 0° or 3° on this wheelchair (you may order with or without the anti-tippers), Invacare strongly recommends ordering the anti-tippers as a safeguard for the wheelchair user.

Seat-to-floor angle of 6°: If changing the seat-to-floor angle to 6°, anti-tippers MUST be ordered and installed.

Anti-tippers MUST be fully engaged and release buttons fully protruding out of adjustment holes.

ALWAYS use anti-tippers. When outdoors on wet, soft ground or on gravel surfaces, anti tippers may not provide the same level of protection against tipover. Extra caution must be observed when traversing such surfaces.

Ensure both anti-tippers are adjusted to the same mounting hole.

Installing Anti-Tippers

NOTE: For this procedure, refer to FIGURE 8.1.

1.Remove plug button (not shown) from end of rear frame tubing and install anti‐rattles if not already installed.

2.Press the release buttons in and insert the anti‐tippers with the anti‐tipper wheels pointing toward the ground/floor into the rear frame tubing until the bottom release button locks in place.

9000 Series

80

Part No. 1076155

Image 80
Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Special Notes Wheelchair TIE-DOWN Restraints and Seat RestraintsLabel Location Important NoticeTypical Product Parameters 9000 SL9000 XT Typical Product Parameters XT Recliner 9000 XDT General Guidelines Stability All ModelsStability Recliner Models Only Anti-TippersOperating Information Tire Pressure Weight TrainingWeight Limitation Safety INSPECTION/TROUBLESHOOTING ChecklistTroubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Adjusting Back Angle Seat and BackAdjusting Back Height SL without Adjustable Back Angle OptionAdjusting Seat Width SL with Adjustable Back Angle Option and 9000 XT/XDTPivot Link Adjusting Seat Width Adjusting Seat Depth 9000XT ModelXDT and 9000 SL Mounting ScrewsSeat and Back Front Caster Mounting Adjustments Front CastersWheelchair Frame Repositioning/Replacing Cam Seat to Floor Changing Seat-to-Floor Height/Seat-to-Floor AngleAngle ‐ a 3 seat‐to‐floor angle is the only available angle Super Low Frame Style Adult/Tall Frame StyleAdult/Hemi Frame Styles AngleForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Quick-Release Axles Removing/Installing Rear WheelsRear Wheels Permanent Axles Detent PinModels with Offset Axle Option Rear Wheels Spacers Adjusting Quick-Release Axle Adjusting Wheelbase LengthRecliner Replacing Release HandleAdjusting Cable Assembly Tension Replacing Release HandleReplacing Cable Assembly Adjusting Cable Assembly TensionConnecting Disconnecting/Connecting Lower Cable AssemblyDisconnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Locking Rod Replacing Back TubeRecliner Removing/Installing Spring Lift Mechanism RemovingInstalling Removing/Installing Spring Lift MechanismReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth Using/Adjusting Wheel Locks Using Attendant Operated Wheel LocksWith Patient Operated Wheel Locks With Attendant Operated Wheel LocksAdjusting Attendant Operated Wheel Locks 14 Using Attendant Operated Wheel Locks15 Adjusting Attendant Operated Wheel Locks Changing Seat-to-Floor HeightInstalling Anti-Tippers 16 Changing Seat-to-Floor HeightRecliner XT Recliner ANTI-TIPPERS/WHEEL Locks Installing/Adjusting Anti-tippersInstalling Anti-Tippers Adjusting Anti-Tippers Installing Anti-TippersUsing/Adjusting Disk Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico
Related manuals
Manual 30 pages 6.48 Kb Manual 60 pages 56.17 Kb