Invacare 9000 XT, 9000XT Recliner, 9000 SL Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle

Page 40

SECTION 5—SEAT TO FLOOR

Refer to the following table to determine the obtainable seat‐to‐floor heights and seat‐to‐floor angles for 22‐inch rear wheels and 8‐inch front casters:

SEAT-TO-FLOOR

SEAT-TO-FLOOR

REFER TO

HEIGHT*

ANGLE

 

 

 

 

19½ inches

6°

Chart 15

 

 

 

18½ inches

3°

Chart 16

 

 

 

18½ inches

6°

Chart 17

 

 

 

17½ inches

0°

Chart 18

 

 

 

17½ inches

3°

Chart 19

 

 

 

17½ inches

6°

Chart 20

 

 

 

*NOTE: The seat‐to‐floor heights are based on urethane tires. If wheelchair is equipped with pneumatic (properly inflated) or solid rubber tires, add ¼ inch to the measurements listed above. These heights can vary +/‐ ¼ inch due to tire wear and manufacturing tolerances.

NOTE: Charts 15 to 20 apply to adult/hemi frame styles only. Refer to the charts for seat‐to‐floor height settings for adult/tall (Adult/Tall Frame Style on page 31) and super low frame styles (Super Low Frame Style on page 31) and Changing Seat‐to‐Floor Height on page 77 for recliner frame styles.

Chart 15 - Seat-to-Floor Height of 19½ inches and 6° Angle

REAR WHEEL POSITION

ANTI-TIP

FRONT CASTER

OFFSET AXLE OPTION

STANDARD

PART/MODEL

MOUNTING

ADJC CAM

NUMBERS

FORWARD*

REARWARD

 

POSITION

POSITION

 

 

 

 

 

 

Hole 1

Hole 1

 

N/A On-Chair

 

Front

 

 

 

 

 

 

1113766 Off-Chair

 

 

Hole 3

Hole 3

 

 

 

 

 

 

 

 

 

Notch

*NOTE: This offset axle plate position requires the caster headtube to be leading to provide adequate tire clearance between the rear tire and the front caster. Refer to Converting from Trailing to Leading or Leading to Trailing Casters on page 27.

9000 Series

40

Part No. 1076155

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Series Reference Documents Table of Contents Rear Wheels Limited Warranty Special Notes Wheelchair TIE-DOWN Restraints and Seat RestraintsLabel Location Important NoticeTypical Product Parameters 9000 SL9000 XT Typical Product Parameters XT Recliner 9000 XDT General Guidelines Stability All ModelsOperating Information Anti-TippersStability Recliner Models Only Weight Limitation Weight TrainingTire Pressure Safety INSPECTION/TROUBLESHOOTING ChecklistTroubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Adjusting Back Angle Seat and BackAdjusting Back Height SL without Adjustable Back Angle OptionAdjusting Seat Width SL with Adjustable Back Angle Option and 9000 XT/XDTPivot Link Adjusting Seat Width Adjusting Seat Depth 9000XT ModelXDT and 9000 SL Mounting ScrewsSeat and Back Front Caster Mounting Adjustments Front CastersWheelchair Frame Repositioning/Replacing Cam Seat to Floor Changing Seat-to-Floor Height/Seat-to-Floor AngleAngle ‐ a 3 seat‐to‐floor angle is the only available angle Super Low Frame Style Adult/Tall Frame StyleAdult/Hemi Frame Styles AngleForward Rearward Numbers Position Forward Rearward Position Forward Rearward Numbers Chart 7 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 9 Seat-to-Floor Height of 17½ inches and 0 Angle Rear Wheel Position ANTI-TIP Front Caster Offset Axle Option Forward Rearward Chart 15 Seat-to-Floor Height of 19½ inches and 6 Angle Rear Wheel Position ANTI-TIP Front Caster Chart 18 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 20 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 21 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 24 Seat-to-Floor Height of 16½ inches and 0 Angle Chart 27 Seat-to-Floor Height of 17½ inches and 0 Angle Chart 29 Seat-to-Floor Height of 18½ inches and 6 Angle Chart 31 Seat-to-Floor Height of 17½ inches and 6 Angle Chart 32 Seat-to-Floor Height of 17½ inches and 3 Angle Chart 35 Seat-to-Floor Height of 16½ inches and 3 Angle Chart 38 Seat-to-Floor Height of 15½ inches and 3 Angle Rear Wheels Removing/Installing Rear WheelsQuick-Release Axles Permanent Axles Detent PinModels with Offset Axle Option Rear Wheels Spacers Adjusting Quick-Release Axle Adjusting Wheelbase LengthRecliner Replacing Release HandleAdjusting Cable Assembly Tension Replacing Release HandleReplacing Cable Assembly Adjusting Cable Assembly TensionDisconnecting Disconnecting/Connecting Lower Cable AssemblyConnecting Recliner Disconnecting/Connecting Lower Cable Assembly Replacing Threaded Sector Replacing Threaded SectorReplacing Locking Rod Replacing Back TubeRecliner Removing/Installing Spring Lift Mechanism RemovingInstalling Removing/Installing Spring Lift MechanismReplacing Recliner Tube Replacing Recliner Tube Adjusting Seat Width Pivot Link 10 Adjusting Seat Width 11 Adjusting Seat Depth Using/Adjusting Wheel Locks Using Attendant Operated Wheel LocksWith Patient Operated Wheel Locks With Attendant Operated Wheel LocksAdjusting Attendant Operated Wheel Locks 14 Using Attendant Operated Wheel Locks15 Adjusting Attendant Operated Wheel Locks Changing Seat-to-Floor HeightInstalling Anti-Tippers 16 Changing Seat-to-Floor HeightRecliner XT Recliner Installing Anti-Tippers Installing/Adjusting Anti-tippersANTI-TIPPERS/WHEEL Locks Adjusting Anti-Tippers Installing Anti-TippersUsing/Adjusting Disk Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Using Patient Operated Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Installing Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsANTI-TIPPERS/WHEEL Locks Limited Warranty Made in Mexico
Related manuals
Manual 30 pages 6.48 Kb Manual 60 pages 56.17 Kb
Top Page Image Contents