Invacare 1143199 manual Operation, Adjusting the Propel Back Depth and Angle

Page 14

SECTION 3—OPERATION

SECTION 3—OPERATION

WARNING

Check ALL fasteners periodically to ensure that mechanical connections and attaching hardware are tightened securely - otherwise injury or damage may occur.

DO NOT continue to use this product if problems are discovered. Corrective main- tenance can be performed at or arranged through your equipment supplier.

Adjusting the Propel Back Depth and Angle

NOTE: For this procedure, refer to FIGURE 3.1.

1.Loosen, but DO NOT remove, the hex bolts securing the back tab to the cane mounting brackets on both sides.

2.Adjust the back to the desired angle and/or depth.

NOTE: Use the measurement marks for as a reference to align the left and right sides. 3. Tighten the hex bolts securing the back tabs to the cane mounting brackets.

Back Tab

Hex Bolts

Back Tab

Plate

Cane Mounting

Bracket

DETAIL “A” - BACK ANGLE

AND DEPTH

Depth

1.75”

Angle27°

Back Tab

Plate

Cane Mounting

Bracket

Measurement

Marks

FIGURE 3.1 Adjusting the Propel Back Depth and Angle

InTouch ™ Propel ™ Back

14

Part No 1143199

Image 14

Contents InTouch Propel Back InTouch Propel Back Special Notes MeaningTable of Contents Register Your ProductProduct Registration Form Fold Here Cut Along Line Important Information Installation WarningsGeneral Guidelines Seating Pressure WarningMaximum Weight Rating Installing Mounting Hardware InstallingInstallation Overview Installing Mounting Hardware Installing/Removing the Propel Back Installing/Removing the Propel BackAdjusting the Propel Back Width Adjusting the Propel Back WidthInstalling/Removing the Propel Back Cushion Installing the CushionAdjusting the Propel Back Depth and Angle OperationReplacing Cushion MaintenanceReplacing Upholstery Cover Cleaning InstructionsBack Assembly FoamLimited Warranty Avertissement Remarques Spéciales SignificationTable DES Matières Remarques Spéciales Directives GénéralesRemarque Importante Avertissements au Sujet de L’installationDirectives Générales Avertissement au Sujet des Points de PressionCharge Maximum Installation Aperçu Général de L’installationInstallation des Ferrures de Montage RemarqueInstallation/Dépose du Dossier Propel DossierRéglage de la Largeur du Dossier Propel Réglage de la Largeur du Dossier PropelInstallation/ Dépose du Coussin du Dossier Propel Installation du CoussinFonctionnement Réglage de la profondeur et de l’angle du dossier PropelEntretien Remplacement de la GarnitureRemplacement du Coussin Garniture Instructions de NettoyageEnsemble du Dossier MousseGarantie Limitée Advertencia Notas Especiales Significado IndicadorTabla DE Contenido Notas Especiales Pautas GeneralesAdvertencia Sobre la Presión del Asiento Pautas GeneralesInformación Importante Advertencias Sobre la InstalaciónCapacidad de Peso Máximo Instalación Descripción General de la InstalaciónInstalación de las Piezas Metálicas Para Montaje De ambos ladosInstalación y Remoción del Respaldo Propel Figura 2.3 Instalación y Remoción del Respaldo PropelAjuste del Ancho del Respaldo Propel Cuadro del respaldoInstalación y Remoción del Almohadón del Respaldo Propel Instalación de los AlmohadonesOperación Ajuste de la Altura y el Ángulo del Respaldo PropelReemplazo del Almohadón MantenimientoReemplazo del Tapizado Funda Instrucciones de LimpiezaConexiones del Respaldo GomaespumaNota Nota Garantía Limitada USA