A&D HW-200KGL, HW-100KGL Installing the Scale, Secure the Column, Stpe 3 Secure the Display Unit

Page 11

5 Installing the Scale

This procedure includes all of the steps for installing the HW-G series scales

Step 1 Unpacking

Remove the weighing pan from the carton and place to one side. Remove the base unit and column from the carton, taking care not to pull on the loadcell cable.

Step 2 Secure the Column

Step 2a Remove the 4 Allen screws from the column lower bracket.

Step 2b Pull the excess loadcell cable through the column as you position the col- umn to the base unit, so as not to damage the loadcell cable. Affix the column to the base unit using four 5mm Allen screws.

Stpe 3 Secure the Display Unit

Step 3a Remove the 2 screws from the rear of the display unit, position the display unit onto the column bracket and pull the excess cable back down the centre of the column to the base unit. Ensure that the cable exits via the cut out in the display unit column bracket and secure the headwork with the 2 screws.

Step 3b Carefully make the connection between the cable connector and J1 inside the headwork, then secure the rear display panel.

Column

Step 2a

Step 1

Base unit Load-cell cable

Step 2b 5mm allen screws

Allen wrench

Step 3

Screws

Step 4 Fit the Pan

Step 4

Step 4 Fold the excess cable at the

basework end and secure with the ‘twist andTie excess cable here tie’ strip provided.

Fit the pan to the base unit.

HW-G Instruction Manual Page 9

HW-G OZIM v1a

Image 11
Contents HW-G Series Page Contents HW-G Ozim v1a Compliance with FCC rules ComplianceOutline and Features Unpacking All AccessoriesType Products Accessories Accessories and Options listOptions List Order code or option name AccessoriesPrecautions for Storing the Scale Precautions for Installing the ScalePrecautions for Operating the Scale Fit the Pan Installing the ScaleSecure the Column Stpe 3 Secure the Display UnitLevel the Scale Adjust the Display UnitConnect the Power Installing the Batteries for Type L Names OFF Display and SymbolsHW-G Ozim v1a Switches HW-G Ozim v1a Memo Basic OperationTurning the Scale On/Off & Basic Weighing Type L with Batteries Semi-Automatic Tare Input by Weighing Tare and Net DisplayMode Switch Changing Unit & Mode Storing a Unit Mass Counting ModeCounting the number of articles Storing a 100% Mass Percentage ModeReading Percentage Function table Meaning & Purpose Operation and SwitchesAccumulation Function Preparation Setting Parameters Example Operation and Performance ExamplesFunction table Meaning and Purpose Comparator FunctionComparator Sign Comparison ConditionSwitch to display an item Step If one Has Been selected, press Case Full/Dribble Batch Function Hold ComparatorFull/Dribble batch sub-function Parameter and display an item of the full/dribble Switch to display the HI Function Table Meaning and purpose Simple batch function Simple Batch FunctionPreparation Setting Parameters Mode Calibration Adjusting the Scale Gravity Acceleration Table Gravity Acceleration Correction Complete Calibration ProcedureCalibration of the Zero Point Function Table Procedure for Setting Parameters15.2 Parameter List Function or full/dribble batch function Display Meaning and purposePrinting condition when using option OP-06 for type Function to hold the current display value. When 16 RS-232C Serial Data Interface Format Data FormatFormat Preparation and Performance Examples Stream ModeTare Command ModeCancel of tare Upper limit value Preset tareFinal value Preparation Setting Parameters 17.1 RS-232C / Relay output / Buzzer OP-03 Pin connections Pin No Signal name Direction DescriptionOptions 17.2 RS-422 / RS-485 / Relay output OP-04 Pin No Signal name Direction DescriptionInstalling OP-04 Communication Format Lower limit value ZeroFinal value Reset of Accumulation data and numberAccumulation data output Accumulation count outputConsumables SpecificationInternal Printer for Type V OP-06 Installation DisassemblyPerformance Check HW-GV HW-G seriesDimensions HW-G Ozim v1a This situation Confirm these items MaintenanceCheck Points Before Calling Maintenance Repair