A&D HW-200KGV, HW-100KGL, HG-60KGV, HW-60KGL, HW-200KGL, HW-10KGV Calibration of the Zero Point

Page 44

14.2.3 Calibration of the Zero Point

Step 8 Press and hold the CAL switch to enter the calibration mode after

displayingnormal weighing for 30 minutes.

Then the Cal 0 is displayed.

Step 9 With nothing on the pan, press the ENTER switch while the stable mark is displayed. The scale stores the current condition as the zero point. .

Step 10 The scale displays 5pn1 for several seconds. If finishing the calibration mode at this stage (Zero calibration only), press CAL to proceed to step 13.

14.2.4 Span Calibration

Step 11 Set the value of the calibration mass using the following switches. (The initial value depends upon the particular model.)

^switch Selecting the value of a digit.

< switch Selecting a digit.

Step 12 Place the mass’ selected at step 11’ onto the pan. When the stable mark is displayed press the ENTER switch.

The scale then calculates the span and stores the value.

Step 13 The scale displays end at the finish.

Remove the mass from the pan.

Step 14 Press the CAL switch to return to the normal weighing mode.

HW-G OZIM v1a

HW-G Instruction Manual Page 42

Image 44

Contents HW-G Series Page Contents HW-G Ozim v1a Compliance Compliance with FCC rulesOutline and Features All Accessories UnpackingAccessories and Options list Type Products AccessoriesOrder code or option name Accessories Options ListPrecautions for Storing the Scale Precautions for Installing the ScalePrecautions for Operating the Scale Installing the Scale Secure the ColumnStpe 3 Secure the Display Unit Fit the PanLevel the Scale Adjust the Display UnitConnect the Power Installing the Batteries for Type L Names Display and Symbols OFFHW-G Ozim v1a Switches HW-G Ozim v1a Memo Basic OperationTurning the Scale On/Off & Basic Weighing Type L with Batteries Tare and Net Display Semi-Automatic Tare Input by WeighingMode Switch Changing Unit & Mode Counting Mode Storing a Unit MassCounting the number of articles Percentage Mode Storing a 100% MassReading Percentage Function table Meaning & Purpose Operation and SwitchesAccumulation Function Preparation Setting Parameters Operation and Performance Examples ExampleComparator Function Comparator SignComparison Condition Function table Meaning and PurposeSwitch to display an item Step If one Has Been selected, press Case Full/Dribble Batch Function Hold ComparatorFull/Dribble batch sub-function Parameter and display an item of the full/dribble Switch to display the HI Simple Batch Function Function Table Meaning and purpose Simple batch functionPreparation Setting Parameters Mode Calibration Adjusting the Scale Gravity Acceleration Table Complete Calibration Procedure Gravity Acceleration CorrectionCalibration of the Zero Point Procedure for Setting Parameters Function Table15.2 Parameter List Display Meaning and purpose Function or full/dribble batch functionPrinting condition when using option OP-06 for type Function to hold the current display value. When 16 RS-232C Serial Data Interface Data Format FormatFormat Stream Mode Preparation and Performance ExamplesTare Command ModeCancel of tare Preset tare Upper limit valueFinal value Preparation Setting Parameters 17.1 RS-232C / Relay output / Buzzer OP-03 Pin connections Pin No Signal name Direction DescriptionOptions Pin No Signal name Direction Description 17.2 RS-422 / RS-485 / Relay output OP-04Installing OP-04 Communication Format Zero Lower limit valueReset of Accumulation data and number Accumulation data outputAccumulation count output Final valueConsumables SpecificationInternal Printer for Type V OP-06 Disassembly InstallationPerformance Check HW-G series HW-GVDimensions HW-G Ozim v1a Maintenance Check Points Before Calling MaintenanceRepair This situation Confirm these items