A&D HG-60KGV, HW-100KGL, HW-60KGL, HW-200KGL, HW-200KGV Operation and Performance Examples, Case

Page 33

11.2 Operation and Performance (Examples)

Example 1

This example is set as follows:
Function table	f6 3	(If the current display value is not near-zero,
		the scale compares the display value with the
		upper limit value and the lower limit value
		immediately.)
Upper limit value (HI)		7.000kg
Lower limit value (LO)		6.500kg

Case

The comparison starts at turning the scale on.

When the current value is less than 6.500kg, LO is displayed.

When the current value is between 6.500kg and 7.000kg, OK is displayed. When the current value is greater than 7.000kg, HI is displayed.

Example 2

This example is set as follows:
Function table		(Pressing the		switch, after the stability
	f6 4		SET
		mark is displayed, the scale compares the
		current display value with the upper limit value
		and the lower limit value immediately.)
Upper limit value (HI)	2.000kg
Lower limit value (LO)	-1.000kg

Case

Pressing the performed.

SET

switch, after displaying the stability mark ,the comparison is

When the current value is less than -1.000kg, LO is displayed.

When the current value is between -1.000kg and 2.000kg, OK is displayed.

When the current value is greater than 2.000kg, HI is displayed.

HW-G Instruction Manual Page 31

HW-G OZIM v1a

Image 33

Contents HW-G Series Page Contents HW-G Ozim v1a Compliance with FCC rules ComplianceOutline and Features Unpacking All AccessoriesType Products Accessories Accessories and Options listOptions List Order code or option name AccessoriesPrecautions for Installing the Scale Precautions for Operating the ScalePrecautions for Storing the Scale Secure the Column Installing the ScaleStpe 3 Secure the Display Unit Fit the PanAdjust the Display Unit Connect the PowerLevel the Scale Installing the Batteries for Type L Names OFF Display and SymbolsHW-G Ozim v1a Switches HW-G Ozim v1a Basic Operation Turning the Scale On/Off & Basic WeighingMemo Type L with Batteries Semi-Automatic Tare Input by Weighing Tare and Net DisplayMode Switch Changing Unit & Mode Storing a Unit Mass Counting ModeCounting the number of articles Storing a 100% Mass Percentage ModeReading Percentage Operation and Switches Accumulation FunctionFunction table Meaning & Purpose Preparation Setting Parameters Example Operation and Performance ExamplesComparator Sign Comparator FunctionComparison Condition Function table Meaning and PurposeSwitch to display an item Step If one Has Been selected, press Case Full/Dribble Batch Function Comparator Full/Dribble batch sub-functionHold Parameter and display an item of the full/dribble Switch to display the HI Function Table Meaning and purpose Simple batch function Simple Batch FunctionPreparation Setting Parameters Mode Calibration Adjusting the Scale Gravity Acceleration Table Gravity Acceleration Correction Complete Calibration ProcedureCalibration of the Zero Point Function Table Procedure for Setting Parameters15.2 Parameter List Function or full/dribble batch function Display Meaning and purposePrinting condition when using option OP-06 for type Function to hold the current display value. When 16 RS-232C Serial Data Interface Format Data FormatFormat Preparation and Performance Examples Stream ModeCommand Mode Cancel of tareTare Upper limit value Preset tareFinal value Preparation Setting Parameters Pin connections Pin No Signal name Direction Description Options17.1 RS-232C / Relay output / Buzzer OP-03 17.2 RS-422 / RS-485 / Relay output OP-04 Pin No Signal name Direction DescriptionInstalling OP-04 Communication Format Lower limit value ZeroAccumulation data output Reset of Accumulation data and numberAccumulation count output Final valueSpecification Internal Printer for Type V OP-06Consumables Installation DisassemblyPerformance Check HW-GV HW-G seriesDimensions HW-G Ozim v1a Check Points Before Calling Maintenance MaintenanceRepair This situation Confirm these items