A&D HG-60KGV, HW-100KGL, HW-60KGL, HW-200KGL, HW-200KGV, HW-10KGV, HW100KGV Disassembly, Installation

Page 65

Installation of OP-06

Caution

This option cannot be used with type L (Liquid Crystal Display) scales.

Packed with the option OP-06 are the following items which are used to install the printer into your scale.

Reference No.	Description	Quantity
6	Printer cover	1
7	Printer unit	1
8	Printer control board	1
a	Self tapping screw	3
b	Screw with washer	4
	Paper roll (PP-156)	1
	Spare ink ribbon (ERC-05)	1

Installation Method

1.Disassembly

a)Disconnect the scale power plug from the AC mains supply socket.

b)Loosen the lock screws and remove the rear cover unit (Item 3)

c)Loosen 4 x screws (Item c) and remove the upper case unit.

d)Remove 2 screws (Item a) and remove the Battery Cover.

2.Installation

(a)Connect CN2, of the printer board (Item 8), to J5 on the main board (Item 1)

(b)Install the printer board (Item 8) to the 4 stand-offs on the board on the upper case (Item 1).

(c)Secure the printer unit (Item 7) to the upper case (Item 1).

(d)Connect the printer unit cable to CN4 on the printer board (Item 8).

HW-G Instruction Manual Page 63

HW-G OZIM v1a

Image 65

Contents HW-G Series Page Contents HW-G Ozim v1a Compliance with FCC rules ComplianceOutline and Features Unpacking All AccessoriesType Products Accessories Accessories and Options listOptions List Order code or option name AccessoriesPrecautions for Storing the Scale Precautions for Installing the ScalePrecautions for Operating the Scale Secure the Column Installing the ScaleStpe 3 Secure the Display Unit Fit the PanLevel the Scale Adjust the Display UnitConnect the Power Installing the Batteries for Type L Names OFF Display and SymbolsHW-G Ozim v1a Switches HW-G Ozim v1a Memo Basic OperationTurning the Scale On/Off & Basic Weighing Type L with Batteries Semi-Automatic Tare Input by Weighing Tare and Net DisplayMode Switch Changing Unit & Mode Storing a Unit Mass Counting ModeCounting the number of articles Storing a 100% Mass Percentage ModeReading Percentage Function table Meaning & Purpose Operation and SwitchesAccumulation Function Preparation Setting Parameters Example Operation and Performance ExamplesComparator Sign Comparator FunctionComparison Condition Function table Meaning and PurposeSwitch to display an item Step If one Has Been selected, press Case Full/Dribble Batch Function Hold ComparatorFull/Dribble batch sub-function Parameter and display an item of the full/dribble Switch to display the HI Function Table Meaning and purpose Simple batch function Simple Batch FunctionPreparation Setting Parameters Mode Calibration Adjusting the Scale Gravity Acceleration Table Gravity Acceleration Correction Complete Calibration ProcedureCalibration of the Zero Point Function Table Procedure for Setting Parameters15.2 Parameter List Function or full/dribble batch function Display Meaning and purposePrinting condition when using option OP-06 for type Function to hold the current display value. When 16 RS-232C Serial Data Interface Format Data FormatFormat Preparation and Performance Examples Stream ModeTare Command ModeCancel of tare Upper limit value Preset tareFinal value Preparation Setting Parameters 17.1 RS-232C / Relay output / Buzzer OP-03 Pin connections Pin No Signal name Direction DescriptionOptions 17.2 RS-422 / RS-485 / Relay output OP-04 Pin No Signal name Direction DescriptionInstalling OP-04 Communication Format Lower limit value ZeroAccumulation data output Reset of Accumulation data and numberAccumulation count output Final valueConsumables SpecificationInternal Printer for Type V OP-06 Installation DisassemblyPerformance Check HW-GV HW-G seriesDimensions HW-G Ozim v1a Check Points Before Calling Maintenance MaintenanceRepair This situation Confirm these items