Invacare 1080556 manual Contracture Assembly Angle Adjustment Figure

Page 67

CONTRACTURE FOOTPLATE OPTION	PROCEDURE 11

CONTRACTURE ASSEMBLY ANGLE ADJUSTMENT (FIGURE 4)

1.Perform one (1) of the following:

A.BILATERAL CONTRACTURE - Remove the mounting screw and locknut used to lock the angle adjustment of the contracture assembly.

B.CONTRACTURE PLATFORM - Remove the two (2) hex screws and locknuts that lock the angle adjustment of the contracture assembly.

2.Lift the contracture support UP/DOWN to achieve the desired angle.

3.Perform one (1) of the following:

A.BILATERAL CONTRACTURE - Align the mounting hole in the contracture support with one (1) of seven (7) mounting holes on the angle adjustment bracket.

B.CONTRACTURE PLATFORM - Align the upper support mounting hole with one (1) of four (4) mounting holes in the angle adjustment plate.

4.Reinstall the mounting screw(s) and locknut(s) to lock the angle adjustment of the contracture assembly. Securely tighten.

BILATERAL CONTRACTURE			CONTRACTURE PLATFORM
	Mounting	Angle	Angle	Locknuts
	Screw	Adjustment	Angle
	Screw	Adjustment	Adjustment Plate
		Bracket	Adjustment Plate
		Bracket		Hex
				Hex
			HOLE #	Screw
			HOLE #
			4	Upper
Locknut			3	Upper
			3	Support
			2	Support
			2
Contracture Support	Mounting		1
Contracture Support		Holes	ANGLE

FIGURE 4- CONTRACTURE ASSEMBLY ANGLE ADJUSTMENT

USING THE OPTIONAL QUICK-RELEASE PIN (FIGURE 5)

NOTE: This procedure applies to the bilateral contracture footplate only.

NOTE: The quick-release pin replaces the mounting screw that is used to lock the angle adjustment of the contracture support.

CONTRACTURE FOOTPLATE OPTION

WARNING

If not installed at time of shipment, the quick-release pin MUST be installed by a qualified technician only, using a 1/8- inch pop rivet.

1.Press the button on the quick-release pin and insert through the contracture sup- port and the angle adjustment bracket.

Angle Adjustment

Bracket

Pop

Rivet

Button	Contracture
Quick-Release Pin	Support
Quick-Release Pin

2. If necessary adjust the angle of the	FIGURE 5 - USING THE OPTIONAL
contracture assembly. Refer to	QUICK-RELEASE PIN
CONTRACTURE ASSEMBLY ANGLE

ADJUSTMENT in this procedure of the manual.

Part No. 1080556 Rev. I

67

Solara™

Image 67

Contents Solara SolaraLimited Solara Table of Contents Procedure 7 TILT-IN-SPACE Special Notes Special NotesLabel Locations Label LocationsHeavy Duty Package only Transport Ready Option only Specifications SpecificationsGeneral Guidelines Information for Healthcare PROFESSIONALS/ AssistantsGeneral Guidelines Anterior Forward TiltStability Warning Procedure General GuidelinesStability ALL Models Stability ALL Models Except ReclinersOperating Information Stability Recliner Models onlyGeneral Warnings Weight Limitation Weight TrainingStability and Balance SAFETY/HANDLING of WheelchairsCoping with Everyday Obstacles Center Gravity Percentage of Weight DistributionUnoccupied Occupied General Guidelines Tipping Curbs Method 2 Wheelchair Without Step Tube Procedure General Guidelines TippingTipping Curbs Method 1 Wheelchair with Step Tubes Method 1 Wheelchair with Step TubesWithout Step Tube Method 2 WheelchairStairways Transferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistSafety Inspection Maintenance Safety Precautions TroubleshootingMaintenance Procedure 2SAFETY InspectionTransporting Transporting the Invacare SolaraTransporting Front Riggings INSTALLING/REMOVING Swingaway Footrest FigureProcedure Front Riggings InstallingHeight Adjustment Ranges Adjusting Swingaway Footrest HeightMFX and 90 Footrests Figure Installing Adjustable Angle FLIP-UP Footplate Hinge Installing Adjustable Angle FLIP-UP Footplate Hinge FigureCOMPOSITE/ARTICULATING Footplate Heel Loop Replacement FigureAdjusting the Legrest Adjusting the Elevating LEGREST/CALFPAD Assembly FigureAdjusting the Calfpad Arms Arms ProcedureInstalling Armrest Removing ArmrestINSTALLING/REMOVING/ADJUSTING Dual Point Armrest Procedure Arms Adjusting ArmrestRear USING/INSTALLING/ADJUSTING Locking Cantilever ArmsUsing Locking Cantilever Arms Figure Adjusting Locking Cantilever ARM Height FigureProcedure Arms Adjusting Locking Cantilever ARM Angle Figure110 120 Using NON-LOCKING Cantilever Arms Figure USING/INSTALLING/ADJUSTING NON-LOCKING Cantilever ArmsAdjusting NON-LOCKING Cantilever ARM Height Figure ARM Angle Detail a Side View of CAMRemoving T-ARMS ARM PAD Replacement for Cantilever Arms FigureINSTALLING/REMOVING T-ARMS Figure Installing T-ARMSAdjusting T-ARM Height Figure Adjusting the T-ARMSAdjusting T-ARM Sockets Figure Procedure Arms Adjusting T-ARM Depth FigureAdjusting T-ARM Transfer Assists AND/OR Side Guards Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureProcedure BACK/SEAT FOLDING/UNFOLDING Back Assembly FigureBACK/SEAT Installing INSTALLING/REMOVING the Stroller Handles FigureRemoving Detail a QUICK-RELEASE PIN Installed Installing FigureRemoving Figure Locked Position Adjusting FigureReplacing INSTALLING/REPLACING Seat Positioning Straps FigureBACK/SEATPROCEDURE INSTALLING/REPLACING the Back Upholstery FigureRear Installing the Seat Cushion FigureWheelchair Front TILT-IN-SPACE Engaging TILT-IN-SPACE FigureTILT-IN-SPACE Procedure TILT-IN-SPACE Adjusting Trigger Release Cables FigurePositioning Tilt Locking Collars Adjusting Upper Tilt Locking Collar FigureTilt Locking Collar Adjusting Lower Tilt Locking Collar WHEELS/FORKS INSTALLING/REMOVING Rear WheelsWHEELS/FORKS QUICK-RELEASE FigureQUICK-RELEASE Axle Adjusting the QUICK-RELEASE Axle FigureProcedure WHEELS/FORKS Permanent Axle Figure Permanent AxleAdjusting Forks Figure SEAT-TO-FLOOR Height AdjustmentFoot Activated Wheel Lock Inch Wheels only Wheel Lock Adjustment FigureProcedure Wheel LOCKS/ANTI-TIPPERS Wheel LOCKS/ ANTI-TIPPERSLOCKS/ -TIPPERS Using the Wheel LocksINSTALLING/ADJUSTING ANTI-TIPPERS Figure Foot Activated Wheel Locks 12-INCH Wheels only FigureANTI-TIPPER Facing Down INSTALLING/ADJUSTING ANTI-TIPPERSRecliner Back Option Recliner Operation FigureRecliner Back Option Recliner Operation Procedure Recliner Back OptionHeadrest Upholstery Adjusting the Recliner CablesReplacing BACK/HEADREST Upholstery Figure Back UpholsteryReplacing the Recliner Cables Figure Installing NEW Recliner CablesRemoving Existing Recliner Cables Detail B Detail aOption Actuator Centered TOO LOW TOO High Replacing the GAS Cylinders FigureReplacing the GAS Cylinders Determining Necessary Adjustments Adjusting the GAS Cylinders FigurePerforming Adjustments Detail B Must TOO TOO Look LOW High Like this Contracture Footplate Option Installing the Contracture Footplate AssemblyProcedure Contracture Footplate Option Installing the Crossmember Assembly FigureDetail B Lock Using the Optional QUICK-RELEASE PIN Figure Contracture Assembly Angle Adjustment FigureAngle Adjustment of the Contracture Bilateral Contracture Contracture Footplate Height Adjustment FigureReplacing the Contracture Footplate Heel Loop Replacing the Contracture Footplate Heel Loop FigureTransport Ready Option Transport Ready OptionSecuring the Wheelchair to the Vehicle Compliance InformationSecurement Points Figure Front Rear Securing the OccupantWHEELCHAIR-ANCHORED Belts Figure WHEELCHAIR-ANCHORED Belts Procedure Transport Ready Option Detail a Pelvic BeltPositioning Belts Figure Transport ReadyPositioning Belts Part No Rev Solara Warranty WarrantyOne Invacare Way