Sprint Nextel SP7084 owner manual Using Mute, Using the Intercom

Page 21

43-5708.fm Page 21 Monday, September 18, 2000 7:56 AM

stations slowly flashes red. While a call is on hold, you can temporarily place the handset on the base or use another line without disconnecting the current call. While a call is on hold, Call Privacy is released, so any station in the system can release the hold.

2.To release a line from hold, select the line button for that line at any station. The station's line indicator lights green. The call then reverts to Call Privacy and other stations cannot join the call.

Note: If you put a call on hold for more than three minutes, the line indicator flashes rap- idly and a beep sounds three times every 30 seconds until you release the hold. If a call has been on hold for eight minutes, the call is automatically disconnected.

USING MUTE

You can temporarily turn off the microphone on the headset, handset, or speakerphone by pressing MUTE so the calling party cannot hear you. MUTE lights. Press MUTE again to resume the conversation. MUTE turns off.

Note: Mute is also released when you press INTERCOM or HOLD, or hang up the line. Re- member to press the appropriate line button to return to the original call when you use the hold or intercom features.

USING THE INTERCOM

You can use the system as a two-way inter- com between stations. The system has two intercom channels, so two intercom conver- sations can occur at the same time. If auto answer is turned on, and you receive an in- tercom call, the station beeps and the inter- com is instantly connected. If auto answer is not turned on, the called station starts ringing with a double ring.

Note: Line 1 must be common to all the sta- tions for the intercom or paging to operate correctly.

1.Lift the handset or press HEADSET, then press INTERCOM. Or, to use the speak- erphone, simply press INTERCOM — you do not need to press SPEAKER. INTER- COM lights and EXT. ?? appears.

2.Enter the extension number of the sta- tion you want to call. INTERCOM CALL and the extension number appear.

Notes:

•If INVALID ID appears, you entered either your station number or an invalid station number. Enter a valid station number.

•If UNABLE TO CALL appears, DND is turned on at the receiving station, you entered an invalid extension number, or the station is on another intercom call. Check the display for the station number. In this case, you cannot make an intercom call.

At the called station, INTERCOM flashes and the ID for the station placing the intercom call appears.

When Automatic Answer is on (see “Using Automatic Answer” on Page 22), INTER- COM and SPEAKER light and the speaker- phone automatically turns on when you receive an intercom call.

If Automatic Answer is off, press INTERCOM to answer the call using the speakerphone. INTERCOM stops flashing and SPEAKER lights. Lift the handset for privacy.

To end an intercom conversation, press IN- TERCOM again, return the handset to the cra- dle, or press SPEAKER or HEADSET.

If you receive an intercom call during a phone conversation, press INTERCOM to an-

Telephone Operation

21

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents SP708 4-Line Phone System Contents Memory Operation Troubleshooting TAD Telephone Answering Device Features FeaturesRead this Before Installation FCC StatementFCC Wants YOU to Know Lightning Important Safety InstructionsFm Page 8 Monday, September 18, 2000 756 AM Quick Look at Your Phone Square Configuration InstallationNon-Square Configuration Private Line Support Planning Your SystemOn a Desk Mounting the SystemOn a Wall or Wall Plate Connecting the AC Adapter Installing the Backup BatteriesBattery Power Levels Attaching the HandsetConnecting a FAX or PC Modem Setting UP the Stations Verifying the Station and Line ConfigurationsPreparation Station Reset Verifying System ConfigurationSetting the Private Line Setting the RingerSetting the Ringer Volume Setting the HANDSET, Headset and Speaker VolumeSetting Always Ring Handset/Headset VolumeUsing a Headset Telephone OperationMaking Calls Transferring Calls Answering CallsConference Calling with Two Outside Lines Answering a Call While You Are On Another LineUsing Flash Using Auto RedialUsing Hold With AnnouncementUsing the Intercom Using MuteUsing Automatic Answer Using Standard Phones with the SystemPaging All Stations Monitoring Other RoomsStoring a Name and Number in Memory Memory OperationEntering a Pause Editing Stored NumbersTesting Stored Emergency Numbers Chain-Dialing Service NumbersDialing a Stored Number Deleting Stored NumbersProgramming Caller ID Caller ID OperationReviewing Caller ID Records Dialing Numbers from a Caller ID RecordCaller ID Messages Storing a Caller ID Record in Memory Deleting RecordsCaller ID Operation with Auto Attendant on Assigning AN Auto Attendant Station Auto Attendant OperationAuto Attendant Station Operation Turning OFF Auto AttendantTAD Operation Recording GreetingsReviewing the Greetings Selecting the Primary Greeting Setting the Greeting ModeSetting the Greeting Timer Setting the TAD to Answer CallsSelecting the Number of Rings Call ScreeningRecording a Memo Recording Incoming MessagesPlaying Messages Recording a ConversationUsing Remote Access Programming a Remote Access CodeDeleting Messages Remote OperationProblem Solution TroubleshootingTroubleshooting Resetting the Time and Date Performing a System UpdateCare Limited One-Year Warranty
Top Page Image Contents