Avaya 700217243 manual Go to the next procedure, Labeling Jacks, on

Page 19

Quick Reference Guide	2 Installing Your System

Follow these steps to wall-mount the module(s):

1Using the enclosed template, mark the screw locations on the wall.

2Hold the processor module against the wall with the line and extension jacks facing left. Leave at least 1 foot (0.3 meters) clearance at the top, front, and right side, and at least 2 feet (0.6 meter) at the bottom and left side.

3Insert a #8 sheet metal screw into the screw hole at the top of the processor module.

4If you are installing a second module, go to Step 5. If you are not installing a second module (stand-alone configuration):

aInsert another #8 sheet metal screw into the screw hole at the bottom of the module.

bTighten the screws until the mounting tracks are snug against the wall. There must be a 3/8 inch (1 cm) gap between the wall and the rest of the module. Do not overtighten the screws or the module will warp and fail to operate.

cGo to the next procedure, “Labeling Jacks,” on page 11.

5Remove the clear plastic protectors from the connectors on the right side of the wall-mounted PARTNER ACS processor module and the module to be added by grasping the tabs on the ends of the protector and lifting.

6Slide the second module onto the PARTNER ACS processor module, making sure the mounting tracks interlock.

7Attach the 2-slot carrier to the top right side of the two modules, properly engaging the connectors on the modules to the carrier.

8Fasten the carrier to the modules by using the two #4 screws included with the carrier.

9Insert the 3-1/2 inch #8 screw into the bottom of the modules. Tighten it until the mounting tracks of the PARTNER ACS processor module are flush against the wall. Do not overtighten or the module will warp. Then go to the next procedure, “Labeling Jacks,” on page 11.

Installing the Control Unit 9

Image 19

Contents Partner Page Copyright Document Avaya Inc Obtaining Products Important Safety Instructions Page Wed like your opinion Page Contents If Something Doesn’t Work Programming Telephone FeaturesSystem Programming Flow Charts Maintaining Your SystemSystem Overview WelcomeSystem Configurations System Components System CapacitySystem Description Components Opre Auxiliary EquipmentGetting Acquainted Overview Installing Your SystemEvaluating the Environment Installing the Control UnitGo to the next procedure, Labeling Jacks, on Wall-Mounting a 5-Slot Carrier and Modules Labeling Jacks Inserting Batteries in the Processor Module Grounding the SystemQuick Reference Guide Initializing the System Checking the LEDs Connecting Lines and Extensions Installing Telephones Installing the CoverConnecting Auxiliary Equipment System Programming Basics Setting Up Your SystemSetting Up Your System Programming Overlays Button Locations Button Locations on Partner Telephones Changing Programming Type Programming ModeUsing Centralized Telephone Programming System Date #101 Setting the Date, Day, and TimeSystem Day #102, Release 2.0 and Earlier System Time #103 Automatic Daylight/Standard Times #126 Assigning LinesCustomizing Extensions Copy Settings #399 Recall Setting Changing Settings to Support PBX or Centrex ServicesDialing Restrictions Speed Dial and Auto Dial Numbers Emergency Phone Number List #406Programming for Voice Messaging Systems Voice Messaging SystemsSetting Up Your System Additional Voice Messaging System Programming Setting Up Your System System Speed Dial Programming System Features5554757 Dialing Restrictions and PermissionsSecurity Alert Allowed Phone Number Lists #407Allowed List Assignments #408 Disallowed Phone Number Lists #404 Disallowed List Assignments #405 Line Access Restriction #302Current restriction appears Outgoing Call Restriction #401 Group...Description Groups of ExtensionsProgramming System Features Automatic Line Selection Programming Telephone FeaturesProgramming Telephone Features Letters Numbers Extension Name DisplayLine Ringing Quick Reference Guide Programming Telephone Features Maintaining Your System Backup and Restore Backup Programming-Automatic #123 Backup Programming-Manual #124 Restore Programming #125 Maintaining Your System Battery Replacement Using a PC Card Quick Reference Guide Check the LEDs Upgrading 1600 DSL and 012E Module FirmwareAdding New Modules Maintaining Your System Replacing Modules Maintaining Your System Replacing Modules in a 5-Slot Carrier Maintaining Your System Adding Lines, Pools, and Extensions Changing System SettingsChanging the System Clock Key Extensions Adding New LinesAdding New Extensions Adding New PoolsSwapping Extensions Your Release Number If Something Doesn’t WorkPress f00ss#123 Clearing a Backup-Failure Alarm012E Module Power Management Problem Check this Telephone ProblemsProblem Check this Telephone Doesn’t Work on Calling ProblemsProblem Check this System Problems ATM DSL Module ProblemsTip/Ring Device Problems System Programming Flow Chart-How to Use System Flow Chart-System System Flow Chart-Lines System Flow Chart-System Speed Dial NumbersSystem Flow Chart-Extensions Pool Extension Assignment Line Access ModeCopy Settings Call WaitingSystem Flow Chart-Dialing Restrictions and Permissions System Flow Chart-Groups System Flow Chart-Auxiliary Equipment To Erase a Feature or Auto Dial Button Centralized Telephone Programming Flow Chart-How to UseTo Program Another Feature at the Same Extension To Change Setting for Another ExtensionCentralized Telephone Programming Flow Chart Contact Closure For voice signaling the first available extensionManual Signaling Touch-Tone EnableExtension Telephone Programming Flow Chart-How to Use Caller ID Inspect Extension Telephone Programming Flow ChartLoudspeaker Paging Group Hunting-Ring/Voice SignalRecord-A-Call