Avaya 700217243 manual Using a PC Card

Page 70

6 Maintaining Your System	Quick Reference Guide

Using a PC Card

Follow these steps to upgrade your system’s software with a PC card:

CAUTION:

Before starting, verify that you have batteries installed in the processor module by viewing the display of the telephone at extension 10.

1If you have a 5-slot carrier, move the carrier’s On/Off switch to the “Off” position (“O”).

2For all types of installations, disconnect the power cord from the wall outlet.

3If you do not have a 5-slot carrier or have a system of Release 4.0 or later, go to Step 4. If you have a 5-slot carrier of Release 3.0 or earlier:

aLoosen the screw on the lower front of the cover.

bPlace one hand on the handle on the bottom front of the cover and place your other hand on the top of the cover, and gently pull the cover up and away from the carrier. Be careful not to break the tabs that attach the cover to the carrier.

CAUTION:

Remove all other PC Cards from the processor before initiating an upgrade.

4To insert the PC Card, hold it with the label facing to the right, and slide it gently into either PC Card slot on the processor module. When inserted properly, the PC Card projects about 1-5/8 inch (4 cm) from the module.

5Power up the system:

aReconnect the power cord.

CAUTION:

The power cord should hang straight down from the connector, flush against the plastic case. Do not install the power cord at an angle to the case or with a loop in it.

bIf you have a 5-slot carrier, move the carrier’s On/Off switch to the “On” position (“–”).

60 Using a PC Card

Image 70

Contents Partner Page Copyright Document Avaya Inc Obtaining Products Important Safety Instructions Page Wed like your opinion Page Contents Maintaining Your System Programming Telephone FeaturesSystem Programming Flow Charts If Something Doesn’t WorkWelcome System OverviewSystem Configurations System Capacity System ComponentsSystem Description Components Auxiliary Equipment OpreGetting Acquainted Installing Your System OverviewInstalling the Control Unit Evaluating the EnvironmentGo to the next procedure, Labeling Jacks, on Wall-Mounting a 5-Slot Carrier and Modules Labeling Jacks Grounding the System Inserting Batteries in the Processor ModuleQuick Reference Guide Initializing the System Checking the LEDs Connecting Lines and Extensions Installing the Cover Installing TelephonesConnecting Auxiliary Equipment Setting Up Your System System Programming BasicsSetting Up Your System Programming Overlays Button Locations Button Locations on Partner Telephones Programming Mode Changing Programming TypeUsing Centralized Telephone Programming System Date #101 Setting the Date, Day, and TimeSystem Day #102, Release 2.0 and Earlier System Time #103 Assigning Lines Automatic Daylight/Standard Times #126Customizing Extensions Copy Settings #399 Recall Setting Changing Settings to Support PBX or Centrex ServicesDialing Restrictions Emergency Phone Number List #406 Speed Dial and Auto Dial NumbersVoice Messaging Systems Programming for Voice Messaging SystemsSetting Up Your System Additional Voice Messaging System Programming Setting Up Your System Programming System Features System Speed DialDialing Restrictions and Permissions 5554757Allowed Phone Number Lists #407 Security AlertAllowed List Assignments #408 Disallowed Phone Number Lists #404 Line Access Restriction #302 Disallowed List Assignments #405Current restriction appears Outgoing Call Restriction #401 Groups of Extensions Group...DescriptionProgramming System Features Programming Telephone Features Automatic Line SelectionProgramming Telephone Features Extension Name Display Letters NumbersLine Ringing Quick Reference Guide Programming Telephone Features Maintaining Your System Backup and Restore Backup Programming-Automatic #123 Backup Programming-Manual #124 Restore Programming #125 Maintaining Your System Battery Replacement Using a PC Card Quick Reference Guide Upgrading 1600 DSL and 012E Module Firmware Check the LEDsAdding New Modules Maintaining Your System Replacing Modules Maintaining Your System Replacing Modules in a 5-Slot Carrier Maintaining Your System Adding Lines, Pools, and Extensions Changing System SettingsChanging the System Clock Adding New Lines Key ExtensionsAdding New Pools Adding New ExtensionsSwapping Extensions If Something Doesn’t Work Your Release NumberClearing a Backup-Failure Alarm Press f00ss#123012E Module Power Management Telephone Problems Problem Check thisProblem Check this Calling Problems Telephone Doesn’t Work onProblem Check this System Problems DSL Module Problems ATMTip/Ring Device Problems System Programming Flow Chart-How to Use System Flow Chart-System System Flow Chart-System Speed Dial Numbers System Flow Chart-LinesSystem Flow Chart-Extensions Call Waiting Line Access ModeCopy Settings Pool Extension AssignmentSystem Flow Chart-Dialing Restrictions and Permissions System Flow Chart-Groups System Flow Chart-Auxiliary Equipment To Change Setting for Another Extension Centralized Telephone Programming Flow Chart-How to UseTo Program Another Feature at the Same Extension To Erase a Feature or Auto Dial ButtonCentralized Telephone Programming Flow Chart Touch-Tone Enable For voice signaling the first available extensionManual Signaling Contact ClosureExtension Telephone Programming Flow Chart-How to Use Extension Telephone Programming Flow Chart Caller ID InspectLoudspeaker Paging Group Hunting-Ring/Voice SignalRecord-A-Call