Avaya 700217243 manual Adding New Modules

Page 73

Quick Reference Guide	6 Maintaining Your System

The firmware upgrade process occurs for one module at a time. After successful completion of the upgrade for one module, the system resets after 3 to 10 seconds and begins the firmware upgrade of the next module, if required. The firmware upgrades begin with modules in the left-most slot to the right-most slot of the carrier. Once a successful firmware upgrade as been completed for all modules, all power LEDs are steady green.

Adding New Modules

Adding new modules to an existing 5-slot carrier is very similar to installing the control unit.

Use these instructions if you are adding modules to an existing 5-slot carrier. If you are upgrading from a stand-alone PARTNER ACS processor module to a 2-slot carrier, see “Wall-Mounting a Stand-Alone Processor Module and a 2-Slot Carrier” on page 8 for instructions.

CAUTION:

Before starting, verify that you have batteries installed in the processor module by viewing the display of the telephone at extension 10.

Follow these steps to add a module to an existing 5-slot carrier:

1Move the On/Off switch to the “Off” position (“O”).

2Remove the power cord from the wall outlet.

3For Release 3.0 and earlier systems, remove the cover: a Loosen the screw on the lower front of the cover.

bPlace one hand on the handle on the bottom front of the cover and place your other hand on the top of the cover, and gently pull the cover up and away from the carrier. Be careful not to break the tabs that attach the cover to the carrier.

4Before installing a module, remove the clear, plastic protector from the connector area on the rear of the module by grasping the tabs on the ends of the protector and lifting.

Adding New Modules 63

Image 73

Contents Partner Page Copyright Document Avaya Inc Obtaining Products Important Safety Instructions Page Wed like your opinion Page Contents System Programming Flow Charts Programming Telephone FeaturesMaintaining Your System If Something Doesn’t WorkSystem Overview WelcomeSystem Configurations System Components System CapacitySystem Description Components Opre Auxiliary EquipmentGetting Acquainted Overview Installing Your SystemEvaluating the Environment Installing the Control UnitGo to the next procedure, Labeling Jacks, on Wall-Mounting a 5-Slot Carrier and Modules Labeling Jacks Inserting Batteries in the Processor Module Grounding the SystemQuick Reference Guide Initializing the System Checking the LEDs Connecting Lines and Extensions Installing Telephones Installing the CoverConnecting Auxiliary Equipment System Programming Basics Setting Up Your SystemSetting Up Your System Programming Overlays Button Locations Button Locations on Partner Telephones Changing Programming Type Programming ModeUsing Centralized Telephone Programming System Date #101 Setting the Date, Day, and TimeSystem Day #102, Release 2.0 and Earlier System Time #103 Automatic Daylight/Standard Times #126 Assigning LinesCustomizing Extensions Copy Settings #399 Recall Setting Changing Settings to Support PBX or Centrex ServicesDialing Restrictions Speed Dial and Auto Dial Numbers Emergency Phone Number List #406Programming for Voice Messaging Systems Voice Messaging SystemsSetting Up Your System Additional Voice Messaging System Programming Setting Up Your System System Speed Dial Programming System Features5554757 Dialing Restrictions and PermissionsSecurity Alert Allowed Phone Number Lists #407Allowed List Assignments #408 Disallowed Phone Number Lists #404 Disallowed List Assignments #405 Line Access Restriction #302Current restriction appears Outgoing Call Restriction #401 Group...Description Groups of ExtensionsProgramming System Features Automatic Line Selection Programming Telephone FeaturesProgramming Telephone Features Letters Numbers Extension Name DisplayLine Ringing Quick Reference Guide Programming Telephone Features Maintaining Your System Backup and Restore Backup Programming-Automatic #123 Backup Programming-Manual #124 Restore Programming #125 Maintaining Your System Battery Replacement Using a PC Card Quick Reference Guide Check the LEDs Upgrading 1600 DSL and 012E Module FirmwareAdding New Modules Maintaining Your System Replacing Modules Maintaining Your System Replacing Modules in a 5-Slot Carrier Maintaining Your System Adding Lines, Pools, and Extensions Changing System SettingsChanging the System Clock Key Extensions Adding New LinesAdding New Extensions Adding New PoolsSwapping Extensions Your Release Number If Something Doesn’t WorkPress f00ss#123 Clearing a Backup-Failure Alarm012E Module Power Management Problem Check this Telephone ProblemsProblem Check this Telephone Doesn’t Work on Calling ProblemsProblem Check this System Problems ATM DSL Module ProblemsTip/Ring Device Problems System Programming Flow Chart-How to Use System Flow Chart-System System Flow Chart-Lines System Flow Chart-System Speed Dial NumbersSystem Flow Chart-Extensions Copy Settings Line Access ModeCall Waiting Pool Extension AssignmentSystem Flow Chart-Dialing Restrictions and Permissions System Flow Chart-Groups System Flow Chart-Auxiliary Equipment To Program Another Feature at the Same Extension Centralized Telephone Programming Flow Chart-How to UseTo Change Setting for Another Extension To Erase a Feature or Auto Dial ButtonCentralized Telephone Programming Flow Chart Manual Signaling For voice signaling the first available extensionTouch-Tone Enable Contact ClosureExtension Telephone Programming Flow Chart-How to Use Caller ID Inspect Extension Telephone Programming Flow ChartLoudspeaker Paging Group Hunting-Ring/Voice SignalRecord-A-Call