AltiGen comm 600H manual Modifying Dhcp Settings, Enabling Dhcp

Page 35

Local	Network>Local	Sets the IP phone’s local address;
Address	Address	only shows if DHCP is disabled.

Network	Network>Network	Sets the IP phone’s network mask;
Mask	Mask	only shows if DHCP is disabled.

Gateway	Network>Gateway	Sets the Gateway IP address.

Enable	Network>Enable/	Set whether GateKeeper is enabled or
Gatekeeper	Disable	disabled.
	GateKeeper
GateKeeper	Network>GK	Set to YES or NO to indicate whether
Discovery	Discovery	GateKeeper discovery is enabled. IP
		Phone will automatically find
		GateKeeper.

Enable NAT	Network>Enable/	Set whether NAT is enabled or
	Disable NAT	disabled.
NAT Address	Network>NAT	Sets the NAT server’s public IP
	Address	address.

Modifying DHCP Settings

Dynamic Host Configuration Protocol (DHCP) automatically assigns IP addresses to devices when they are connected to the network.

Enabling DHCP

The Alti-IP 600H automatically enables DHCP by default, but you can reset the protocol if it becomes disabled using the following steps:

1.Press * * 7 + ENTER button.

2. Use / to select Network, then press the Enter key.

3.Scroll to Enable DHCP.

If DHCP is disabled, the option displays as DHCP Enabled NO.

4. Press (DOWN key) to enable DHCP.

Alti-IP 600H Manual 25

Image 35

Contents Administration Manual Trademarks Contents Configuring Phone Settings Glossary Index Alti-IP 600H Manual What The Warranty Covers WarrantyEffect of State Law Overview Preface About This ManualRelated Documentation An Overview of the Alti-IP 600H Alti-IP 600H, Top View Lamp Field key, an AltiServ feature code, a speed New in Version Level Hardware ComponentsHeadset port support Call Record Alti-IP 600H Manual Network Requirements AltiAdmin/ACM Admin Configuration RequirementsSystem & Network Requirements System RequirementsNormal Operation AltiGen IP Phone ServicePlug and Play Feature Basic ModeManual Setup InstallationIP Phone Configuration Window Parameter Description Demand to Extension VM must be enabled in the Personal Configuration screen on the General page, Record onTftp To connect the Alti-IP 600H Configuring the AltiWare IP Settings Plug and Play Setup Before IP Phone is Started Plug and Play SetupPlug and Play Setup After IP Phone is Started Remote Installation Verifying the Phone Startup Process Resolving Errors Upon StartupConfiguring Phone Setting Soft Keys Restoring Default SettingsRebooting the Alti-IP 600H Headset Port Support Dialing an IP Number Directly from the Alti-IP 600HOperation Notes Setting Menu Path Sub Menu Description Configuring Phone SettingsSystem Settings Network Settings Enabling Dhcp Modifying Dhcp SettingsAssigning a Local IP Address Configuring IP SettingsDisabling Dhcp Updating Phone Firmware Assigning a Tftp ServerSystemVersion Info Assigning NAT Configuring NATSetting Ring Tones Press * * 6 Enter Workgroup Status DisplayFWD forwarding Activity DisplayAlti-IP 600H Manual Go to AltiGen IP Phone Feature Description Configuration NotesConfiguration on Phone FunctionsVM in the Personal Call Extension ConfigurationTo AltiGen IP Phone RecordHeadset LED for Parked Call Line ParkCall Line button Then, go to AltiGen IP Phone Configuration Station SpeedAlti-IP 600H Manual Appendix a SpecificationsClient Server TroubleshootingFirewall Considerations Contact AltiGen Technical Support Problem/Symptom SolutionTroubleshooting Message Definition Local Menu Configuration MessagesLCD Messages Alti-IP 600H/600PH Running MessagesLCD Messages User Reference IP Phone Boot MessagesUser Reference Configuration BLF Feature Codes Call Management Dual Tone Multi Frequency see Dtmf GlossaryAlti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Index DSL Alti-IP 600H Manual