AltiGen comm 600H manual Plug and Play Setup After IP Phone is Started

Page 27

If the phone successfully passes through these stages, the phone shows the time and extension in the LCD screen and is now in normal operating mode.

Otherwise, refer to “Troubleshooting” on page 40.

8.If you wish to change soft keys, you can set up IP Phone properties in AltiWare as described in Step 2 - “AltiAdmin/ACM Admin Setup - AltiGen IP Phone Configuration Window” on page 9.

Plug and Play Setup After IP Phone is Started

If you have already started your phone, and wish to execute the Plug and Play feature, perform the following steps:

1.Power up the IP phone (the phone should be in basic mode).

2.Press * * 7 + ENTER to go to the IP phone configuration menu.

3.Press * * 2 + ENTER to restore default settings.

4.Reboot the phone (by unplugging the power and replugging OR

pressing (BACK key) until in Basic mode. The IP phone will automatically go to normal operating mode after reboot.

5.Enter extension number and password.

6.The time and extension is displayed in the LCD screen after the phone has been successfully logged on to AltiServ.

7.Set up IP Phone properties in AltiWare as described in Step 2 - “AltiAdmin/ACM Admin Setup - AltiGen IP Phone Configuration Window” on page 9.

8.Setup is complete. For further configuration of settings for the Alti-IP 600H/600PH, refer to “Configuring Phone Settings” on page 23.

Alti-IP 600H Manual 17

Image 27

Contents Administration Manual Trademarks Contents Configuring Phone Settings Glossary Index Alti-IP 600H Manual What The Warranty Covers WarrantyEffect of State Law Overview Preface About This ManualRelated Documentation An Overview of the Alti-IP 600H Alti-IP 600H, Top View Lamp Field key, an AltiServ feature code, a speed New in Version Level Hardware ComponentsHeadset port support Call Record Alti-IP 600H Manual Network Requirements AltiAdmin/ACM Admin Configuration RequirementsSystem & Network Requirements System RequirementsNormal Operation AltiGen IP Phone ServicePlug and Play Feature Basic ModeManual Setup InstallationIP Phone Configuration Window Parameter Description Demand to Extension VM must be enabled in the Personal Configuration screen on the General page, Record onTftp To connect the Alti-IP 600H Configuring the AltiWare IP Settings Plug and Play Setup Before IP Phone is Started Plug and Play SetupPlug and Play Setup After IP Phone is Started Remote Installation Verifying the Phone Startup Process Resolving Errors Upon StartupRestoring Default Settings Rebooting the Alti-IP 600HConfiguring Phone Setting Soft Keys Headset Port Support Dialing an IP Number Directly from the Alti-IP 600HOperation Notes Configuring Phone Settings System SettingsSetting Menu Path Sub Menu Description Network Settings Enabling Dhcp Modifying Dhcp SettingsConfiguring IP Settings Disabling DhcpAssigning a Local IP Address Updating Phone Firmware Assigning a Tftp ServerSystemVersion Info Configuring NAT Setting Ring TonesAssigning NAT Press * * 6 Enter Workgroup Status DisplayFWD forwarding Activity DisplayAlti-IP 600H Manual Go to AltiGen IP Phone Feature Description Configuration NotesConfiguration on Phone FunctionsVM in the Personal Call Extension ConfigurationTo AltiGen IP Phone RecordHeadset Park Call Line buttonLED for Parked Call Line Then, go to AltiGen IP Phone Configuration Station SpeedAlti-IP 600H Manual Appendix a SpecificationsTroubleshooting Firewall ConsiderationsClient Server Contact AltiGen Technical Support Problem/Symptom SolutionTroubleshooting Message Definition Local Menu Configuration MessagesLCD Messages Alti-IP 600H/600PH Running MessagesLCD Messages User Reference IP Phone Boot MessagesUser Reference Configuration BLF Feature Codes Call Management Dual Tone Multi Frequency see Dtmf GlossaryAlti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Index DSL Alti-IP 600H Manual