AltiGen comm 600H manual Configuring NAT, Assigning NAT, Setting Ring Tones

Page 39

Configuring NAT

NAT (Network Address Translation) is the translation of an IP address used within one network to a different IP address known within another network. One network is designated as the inside network, the other is the outside. The Alti-IP 600H can be enabled to support H.323 behind NAT. The Alti-IP 600H will be able to work behind a regular NAT router without any special implementation for H.323.

For more detailed information regarding NAT configuration guidelines and implementation, refer to the AltiWare OE/ACC or ACM System Administration Manual.

Note: If more than one Alti-IP 600H phone sits behind NAT, a VPN tunnel is required to connect between the NAT router and the corporate router.

Assigning NAT

By default, NAT is not enabled. If you connect the Alti-IP 600H behind a NAT router, you may manually assign the NAT router’s public IP address to this field.

To assign the NAT address, use the following steps:

1.Press * * 7 + ENTER button.

2. Use / to select Network, then press the ENTER button.

3.Scroll to Enable NAT.

4. Press (DOWN key) to select YES.

5.Press the ENTER button.

6. Use (BACK key) to return to the Network menu, then select NAT Address.

Use the buttons on the dial pad to enter the new NAT address, using the * key to enter periods. Use (BACK key) to correct any mistakes.

7.Press the ENTER button.

Setting Ring Tones

The Alti-IP 600H Phone has three (3) ringing tones available. To set the ring tone:

Alti-IP 600H Manual 29

Image 39

Contents Administration Manual Trademarks Contents Configuring Phone Settings Glossary Index Alti-IP 600H Manual What The Warranty Covers WarrantyEffect of State Law Overview Preface About This ManualRelated Documentation An Overview of the Alti-IP 600H Alti-IP 600H, Top View Lamp Field key, an AltiServ feature code, a speed New in Version Level Hardware ComponentsHeadset port support Call Record Alti-IP 600H Manual Network Requirements AltiAdmin/ACM Admin Configuration RequirementsSystem & Network Requirements System RequirementsNormal Operation AltiGen IP Phone ServicePlug and Play Feature Basic ModeManual Setup InstallationIP Phone Configuration Window Parameter Description Demand to Extension VM must be enabled in the Personal Configuration screen on the General page, Record onTftp To connect the Alti-IP 600H Configuring the AltiWare IP Settings Plug and Play Setup Before IP Phone is Started Plug and Play SetupPlug and Play Setup After IP Phone is Started Remote Installation Verifying the Phone Startup Process Resolving Errors Upon StartupRestoring Default Settings Rebooting the Alti-IP 600HConfiguring Phone Setting Soft Keys Headset Port Support Dialing an IP Number Directly from the Alti-IP 600HOperation Notes Configuring Phone Settings System SettingsSetting Menu Path Sub Menu Description Network Settings Enabling Dhcp Modifying Dhcp SettingsConfiguring IP Settings Disabling DhcpAssigning a Local IP Address Updating Phone Firmware Assigning a Tftp ServerSystemVersion Info Configuring NAT Setting Ring TonesAssigning NAT Press * * 6 Enter Workgroup Status DisplayFWD forwarding Activity DisplayAlti-IP 600H Manual Go to AltiGen IP Phone Feature Description Configuration NotesConfiguration on Phone FunctionsVM in the Personal Call Extension ConfigurationTo AltiGen IP Phone RecordHeadset Park Call Line buttonLED for Parked Call Line Then, go to AltiGen IP Phone Configuration Station SpeedAlti-IP 600H Manual Appendix a SpecificationsTroubleshooting Firewall ConsiderationsClient Server Contact AltiGen Technical Support Problem/Symptom SolutionTroubleshooting Message Definition Local Menu Configuration MessagesLCD Messages Alti-IP 600H/600PH Running MessagesLCD Messages User Reference IP Phone Boot MessagesUser Reference Configuration BLF Feature Codes Call Management Dual Tone Multi Frequency see Dtmf GlossaryAlti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Index DSL Alti-IP 600H Manual