AltiGen comm 600H manual Configuring IP Settings, Disabling Dhcp, Assigning a Local IP Address

Page 36

Disabling DHCP

If you do not use DHCP in your network, you can disable DHCP before manually assigning an IP address to the Alti-IP 600H. To disable DHCP, use the following steps:.

Note: Procedures involving configuring IP settings cannot be completed when DHCP is enabled in your network.

1.Press * * 7 + ENTER button.

2. Use / to select Network, then press the Enter key.

3.Scroll to Enable DHCP.

If DHCP is enabled, the option displays as DHCP Enabled YES.

4. Press (DOWN key) to disable DHCP.

Configuring IP Settings

Use these guidelines when manually configuring the IP settings:

•Ensure the default gateway IP address in on the same subnet as the host IP address.

•When inputting IP addresses into the Alti-IP 600H, use the * key to enter periods. For example, “209.120.12.8” would be inputted as “209*120*12*8”.

Assigning a Local IP Address

The IP address is the unique logical address identifying each host computer on a TCP/IP network. An IP address is a 32-bit number expresses as four decimal numbers from 0 to 255 separated by periods.

To assign an IP address, use the following steps:

1.Press * * 7 + ENTER button.

2. Use / to select Network, then press the ENTER button.

3.Scroll to Local Address.

4. Press the ENTER button or (FORWARD key).

5.Use the buttons on the dial pad to enter a new IP address, using the *

key to enter periods. Use the (BACK key) to correct any mistakes.

6.Press the ENTER button.

Alti-IP 600H Manual 26

Image 36

Contents Administration Manual Trademarks Contents Configuring Phone Settings Glossary Index Alti-IP 600H Manual Warranty What The Warranty CoversEffect of State Law Preface About This Manual OverviewRelated Documentation An Overview of the Alti-IP 600H Alti-IP 600H, Top View Lamp Field key, an AltiServ feature code, a speed Hardware Components New in Version LevelHeadset port support Call Record Alti-IP 600H Manual AltiAdmin/ACM Admin Configuration Requirements System & Network RequirementsSystem Requirements Network RequirementsAltiGen IP Phone Service Plug and Play FeatureBasic Mode Normal OperationInstallation Manual SetupIP Phone Configuration Window Parameter Description Configuration screen on the General page, Record on Demand to Extension VM must be enabled in the PersonalTftp To connect the Alti-IP 600H Configuring the AltiWare IP Settings Plug and Play Setup Plug and Play Setup Before IP Phone is StartedPlug and Play Setup After IP Phone is Started Remote Installation Resolving Errors Upon Startup Verifying the Phone Startup ProcessRestoring Default Settings Rebooting the Alti-IP 600HConfiguring Phone Setting Soft Keys Dialing an IP Number Directly from the Alti-IP 600H Headset Port SupportOperation Notes Configuring Phone Settings System SettingsSetting Menu Path Sub Menu Description Network Settings Modifying Dhcp Settings Enabling DhcpConfiguring IP Settings Disabling DhcpAssigning a Local IP Address Assigning a Tftp Server Updating Phone FirmwareSystemVersion Info Configuring NAT Setting Ring TonesAssigning NAT Workgroup Status Display Press * * 6 EnterActivity Display FWD forwardingAlti-IP 600H Manual Feature Description Configuration Notes Configuration onPhone Functions Go to AltiGen IP PhoneExtension Configuration To AltiGen IP PhoneRecord VM in the Personal CallHeadset Park Call Line buttonLED for Parked Call Line Configuration Station Speed Then, go to AltiGen IP PhoneAlti-IP 600H Manual Specifications Appendix aTroubleshooting Firewall ConsiderationsClient Server Problem/Symptom Solution Contact AltiGen Technical SupportTroubleshooting Local Menu Configuration Messages LCD MessagesAlti-IP 600H/600PH Running Messages Message DefinitionLCD Messages IP Phone Boot Messages User ReferenceUser Reference Configuration BLF Feature Codes Call Management Glossary Dual Tone Multi Frequency see DtmfAlti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Index DSL Alti-IP 600H Manual