AltiGen comm manual Restoring Default Settings, Rebooting the Alti-IP 600H

Page 30

•LED 2 light on = network failed

•LED 3 light on = DHCP failed

•LED 4 light on = attached IP address failed

If the phone successfully passes through these stages, it has started up properly. Otherwise, refer to “Troubleshooting” on page 40.

Active Logon While Another Handset is Already Logged On To the Same Extension

If another analog phone or IP phone is already logged on to the same extension, rebooting the Alti-IP 600H will not register the phone successfully. The user must press #26 on the associated physical phone/IP phone, then on the IP phone, use #27 + ENTER to actively log onto AltiServ. Once the extension is logged on and activated, the calls will then be redirected to this IP Phone.

Important:Also, the user should not use the VM option to logon the Alti-IP 600H.

Restoring Default Settings

To automatically restore the original default settings for the Alti-IP 600H:

1.Press * * 7, then press the ENTER button

2.Press * * 2, then press the ENTER button.

Rebooting the Alti-IP 600H

To reboot the Alti-IP 600H, press * * 3, then press the ENTER button.

Note: When the Alti-IP 600H is rebooted, the AltiWare IP address setting is set back to the original configuration.

Configuring “Phone Setting” Soft Keys

When the soft key is set to “Phone Setting” (in the IP Phone Configuration window of AltiAdmin), the IP Phone user can configure the soft key to store a speed dial number or feature code.

To configure a soft key with phone setting enabled:

Alti-IP 600H Manual 20

Image 30

Contents Administration Manual Trademarks Contents Configuring Phone Settings Glossary Index Alti-IP 600H Manual Warranty What The Warranty CoversEffect of State Law Preface About This Manual OverviewRelated Documentation An Overview of the Alti-IP 600H Alti-IP 600H, Top View Lamp Field key, an AltiServ feature code, a speed Hardware Components New in Version LevelHeadset port support Call Record Alti-IP 600H Manual System Requirements AltiAdmin/ACM Admin Configuration RequirementsSystem & Network Requirements Network RequirementsBasic Mode AltiGen IP Phone ServicePlug and Play Feature Normal OperationInstallation Manual SetupIP Phone Configuration Window Parameter Description Configuration screen on the General page, Record on Demand to Extension VM must be enabled in the PersonalTftp To connect the Alti-IP 600H Configuring the AltiWare IP Settings Plug and Play Setup Plug and Play Setup Before IP Phone is StartedPlug and Play Setup After IP Phone is Started Remote Installation Resolving Errors Upon Startup Verifying the Phone Startup ProcessRestoring Default Settings Rebooting the Alti-IP 600HConfiguring Phone Setting Soft Keys Dialing an IP Number Directly from the Alti-IP 600H Headset Port SupportOperation Notes Configuring Phone Settings System SettingsSetting Menu Path Sub Menu Description Network Settings Modifying Dhcp Settings Enabling DhcpConfiguring IP Settings Disabling DhcpAssigning a Local IP Address Assigning a Tftp Server Updating Phone FirmwareSystemVersion Info Configuring NAT Setting Ring TonesAssigning NAT Workgroup Status Display Press * * 6 EnterActivity Display FWD forwardingAlti-IP 600H Manual Phone Functions Feature Description Configuration NotesConfiguration on Go to AltiGen IP PhoneRecord Extension ConfigurationTo AltiGen IP Phone VM in the Personal CallHeadset Park Call Line buttonLED for Parked Call Line Configuration Station Speed Then, go to AltiGen IP PhoneAlti-IP 600H Manual Specifications Appendix aTroubleshooting Firewall ConsiderationsClient Server Problem/Symptom Solution Contact AltiGen Technical SupportTroubleshooting Alti-IP 600H/600PH Running Messages Local Menu Configuration MessagesLCD Messages Message DefinitionLCD Messages IP Phone Boot Messages User ReferenceUser Reference Configuration BLF Feature Codes Call Management Glossary Dual Tone Multi Frequency see DtmfAlti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Alti-IP 600H Manual Index DSL Alti-IP 600H Manual