Xantrex Technology XC3012, XC5012 Mounting, To remotely mount the display, To mount the XC Series

Page 34

Installation

To remotely mount the display:

1.Remove the display as described on page 2–7.

2.Secure the blank plate in the display socket as described.

3.Ensure that the extension cable used for the remote display is long enough to suit the installation. A standard North American style, 4 conductor (RJ-11) telephone cable extender is adequate.

4.Use the enclosed mounting template to cut a hole for the display in the chosen mounting surface.

Take care that there is nothing behind the surface for you to damage.

5.Feed the remote display extension cable through the hole and route it to the charger. Be careful not to damage the telephone connector locking tab when routing the cable. You can use some tape to protect the locking tab from catching on something and breaking off when routing the cable.

6.Remove the adhesive backing on the back of the display.

7.Line up the display with the mounting hole.

8.Firmly press the flanges in place. Do not press in the middle of the display.

9.Once the XC Series is mounted, plug the cable into the bottom connector on the rear panel of the XC Series.

10.Proceed to “Mounting”.

Mounting

Mount the XC Series using the mounting slots provided.

For marine installations, only the mounting configurations with a check mark in Figure 1-6 on page 1–11 meet the North American and European requirements. This is to ensure that any moisture that may be present will not enter the XC Series.

Important: Be sure to measure your AC and DC cables and plan the routing of the cables before drilling the pilot holes for mounting the XC Series.

To mount the XC Series:

1.Keep the carton and packing material in case you need to return the XC Series for servicing.

2.Ensure that you have selected a mounting surface that is clear, flat and allows for a minimum of 76 mm (3 in.) of clearance on each end for fan circulation.

2–8

975-0187-01-01

Image 34
Contents Battery Charger Owner’s GuidePage Xantrex XC3012, XC5012 XC1524 and XC2524 Battery Charger Date and Revision Audience PurposeScope OrganizationConventions Used Related InformationImportant Safety Instructions Explosive Gas and Battery Precautions FCC Information Viii Contents Specifications TroubleshootingOperation Introduction XC Series provides the following standard features XC Series provides the following protection featuresXC Series Appearance XC SeriesInformation Centers of the XC Series Remote DisplayInformation Centers of the XC Series CHf Onboard Status PanelRear Panel DescriptionPreparing for Installation 5XC Series SystemTools and Materials You need the following materialsLocation Condition Requirement6XC Series Mounting Orientations Wiring Requirements DC WiringAC Wiring Over-current protection disconnectBattery Bank Size Requirements Installation Installing the XC Series Installation SequencePre-Installing DC Wiring To install DC wiringPre-Installing AC Wiring To install AC wiringConductor Color code To connect AC wires with the crimp-on butt-splice connector To remove the display Mounting the Remote DisplayTo secure the display or blank plate on the unit To remotely mount the display MountingTo mount the XC Series Grounding Final Connections Shows the connection orderFinal DC Connections To make the last DC connectionsPowering Up To make the last AC connectionsBattery Temperature Sensor Installing Optional AccessoriesTo install a BTS Drip Protection Rubber Boots To install rubber bootsConfiguring the XC Series To configure the battery bank typeTo configure the charging type Operation About Charging Multiplex 3-Stage ChargingSequential 2-Stage Charging To force a battery detection sequenceCharging Overview Temperature Considerations Disqualified BatteriesThings to be aware Perform these disqualification checks in the order shownCharging Batteries To charge your batteriesCharging Batteries Equalizing Flooded Batteries About EqualizingPerforming An Equalization To equalize your batteriesThere are two ways to turn the XC Series on Transitioning the XC Series to On, Disabled or OffThere are two ways to disable the XC Series There is only one way to safely turn the XC Series offAccessing Charger Information Reading Remote Display and Onboard Status Indicator LightsABS Cerr Reporting While Charging or EqualizingReporting While Disabled Reporting While Battery MonitoringTo view the present status of the banks Using a Generator As Source Power Page Troubleshooting Care and Maintenance To clean battery terminalsIndicator Light Flashing Sequences 1Indicator Light Sequences on the XC SeriesError Messages on Remote Display 2Error MessagesErr Bat Problem Solving SymptomFault indicator light flashes. XC Series stops functioning Rdy Page Specifications Physical Specifications Electrical SpecificationsAC Input Specifications AC Input SpecificationsTemperature Specifications Protection FeaturesApprovals EMCPage Warranty and Product Information Limited Warranty forDisclaimer of Warranty Return Material Authorization Policy Information About Your System Page Xantrex Technology Inc