Xantrex Technology XC2524, XC5012, XC3012, XC1524 manual Indicator Light Flashing Sequences

Page 61

Indicator Light Flashing Sequences

Indicator Light Flashing Sequences

Table 4-1Indicator Light Sequences on the XC Series

 

Activity

Charger status

 

 

 

 

 

 

 

 

Charging indicator light illuminates

The unit is charging in bulk or absorption mode

 

 

 

 

 

Charging indicator light flashes

The unit is performing the equalization charge.

 

 

(Charging indicator light flashes once every four

 

 

seconds if bank 1 is being equalized, twice every

 

 

four seconds if bank 2 is being equalized, and

 

 

three times every four seconds if bank 3 is being

 

 

equalized)

 

 

 

 

 

 

 

 

Ready indicator light illuminates

The unit is either in float mode of three stage

 

 

charging or rest mode of two stage charging. All

 

 

batteries have been fully charged.

 

 

 

 

 

Fault indicator light illuminates

Any fault condition that prevents the charger from

 

 

charging one or more banks, but is not a charger

 

 

fault condition - remote display shows details of

 

 

fault. Example:

 

(battery reverse

 

 

err

ErrCHfBATPoL

 

 

polarity detected)

 

 

 

Fault indicator light flashes

Charger fault condition - remote display shows

 

 

followed by

. The charger is damaged,

 

 

contact service.

 

 

 

 

Charging current indicator lights

These lights indicate the charging current. At

 

illuminate

transition points when the current is changing, two

 

 

indicator lights may flash alternately, then settle

 

 

into the new charging current reading.

 

Charging current indicator lights

100% indicator light flashes to indicate battery

 

flash

temperature too high warning (> 50 °C, 122 °F)

 

 

10% indicator light flashes to indicate battery

 

 

temperature too low warning (< 0 °C, 32 °F)

 

 

25% indicator light flashes to indicate that a

 

 

battery has been disqualified (see page 3–4)

 

 

 

 

 

Charging current indicator lights

100% indicator light flashes to indicate battery

 

flash,

temperature too high fault (> 55 °C, 131 °F)

 

Fault indicator light illuminated

10% indicator light flashes to indicate battery

 

 

temperature too low fault (< -20 °C, -4 °F)

 

 

 

 

 

 

 

 

 

 

 

 

975-0187-01-01

 

 

4–3

Image 61
Contents Owner’s Guide Battery ChargerPage Xantrex XC3012, XC5012 XC1524 and XC2524 Battery Charger Date and Revision Scope PurposeAudience OrganizationRelated Information Conventions UsedImportant Safety Instructions Explosive Gas and Battery Precautions FCC Information Viii Contents Specifications TroubleshootingOperation Introduction XC Series provides the following protection features XC Series provides the following standard featuresXC Series XC Series AppearanceRemote Display Information Centers of the XC SeriesInformation Centers of the XC Series Onboard Status Panel CHfDescription Rear Panel5XC Series System Preparing for InstallationYou need the following materials Tools and MaterialsCondition Requirement Location6XC Series Mounting Orientations DC Wiring Wiring RequirementsOver-current protection disconnect AC WiringBattery Bank Size Requirements Installation Installation Sequence Installing the XC SeriesTo install DC wiring Pre-Installing DC WiringTo install AC wiring Pre-Installing AC WiringConductor Color code To connect AC wires with the crimp-on butt-splice connector To remove the display Mounting the Remote DisplayTo secure the display or blank plate on the unit To remotely mount the display MountingTo mount the XC Series Grounding Shows the connection order Final ConnectionsTo make the last DC connections Final DC ConnectionsTo make the last AC connections Powering UpBattery Temperature Sensor Installing Optional AccessoriesTo install a BTS To install rubber boots Drip Protection Rubber BootsTo configure the battery bank type Configuring the XC SeriesTo configure the charging type Operation Multiplex 3-Stage Charging About ChargingSequential 2-Stage Charging To force a battery detection sequenceCharging Overview Disqualified Batteries Temperature ConsiderationsPerform these disqualification checks in the order shown Things to be awareTo charge your batteries Charging BatteriesCharging Batteries About Equalizing Equalizing Flooded BatteriesTo equalize your batteries Performing An EqualizationThere are two ways to disable the XC Series Transitioning the XC Series to On, Disabled or OffThere are two ways to turn the XC Series on There is only one way to safely turn the XC Series offReading Remote Display and Onboard Status Indicator Lights Accessing Charger InformationABS Reporting While Charging or Equalizing CerrReporting While Disabled Reporting While Battery MonitoringTo view the present status of the banks Using a Generator As Source Power Page Troubleshooting To clean battery terminals Care and Maintenance1Indicator Light Sequences on the XC Series Indicator Light Flashing Sequences2Error Messages Error Messages on Remote DisplayErr Bat Symptom Problem SolvingFault indicator light flashes. XC Series stops functioning Rdy Page Specifications Electrical Specifications Physical SpecificationsAC Input Specifications AC Input SpecificationsProtection Features Temperature SpecificationsEMC ApprovalsPage Limited Warranty for Warranty and Product InformationDisclaimer of Warranty Return Material Authorization Policy Information About Your System Page Xantrex Technology Inc