Xantrex Technology XC3012, XC5012, XC2524, XC1524 manual Powering Up, To make the last AC connections

Page 38

Installation

8.Secure cables in place using tie-wraps, P-clamps or cable straps according to electrical codes. Coil and tie any extra BTS or remote display extension cable.

9.The DC breakers may be closed or fuses inserted at this time.

Final AC Connections

To make the last AC connections:

1.Complete the installation by routing the AC cable to the AC source.

2.Connect the AC cable to the AC disconnect breaker and ground in accordance with the color codes on page 2–5.

3.Secure cables in place using tie-wraps, P-clamps or cable straps according to electrical codes.

Powering Up

Make one last check that all connections and connectors are secure.

The XC Series charger may now be powered up. Switch the AC power on at the source breaker. It is normal to see a 7-10 second delay while the unit powers up. During this time, the indicator lights on the onboard status panel and the remote display will not display any information.

At very low AC source voltages (for example, less than 105 VAC) the start up time will increase proportionally up to as much as 40 seconds.

2–12

975-0187-01-01

Image 38
Contents Battery Charger Owner’s GuidePage Xantrex XC3012, XC5012 XC1524 and XC2524 Battery Charger Date and Revision Audience PurposeScope OrganizationConventions Used Related InformationImportant Safety Instructions Explosive Gas and Battery Precautions FCC Information Viii Contents Operation TroubleshootingSpecifications Introduction XC Series provides the following standard features XC Series provides the following protection featuresXC Series Appearance XC SeriesInformation Centers of the XC Series Remote DisplayInformation Centers of the XC Series CHf Onboard Status PanelRear Panel DescriptionPreparing for Installation 5XC Series SystemTools and Materials You need the following materialsLocation Condition Requirement6XC Series Mounting Orientations Wiring Requirements DC WiringAC Wiring Over-current protection disconnectBattery Bank Size Requirements Installation Installing the XC Series Installation SequencePre-Installing DC Wiring To install DC wiringPre-Installing AC Wiring To install AC wiringConductor Color code To connect AC wires with the crimp-on butt-splice connector To secure the display or blank plate on the unit Mounting the Remote DisplayTo remove the display To mount the XC Series MountingTo remotely mount the display Grounding Final Connections Shows the connection orderFinal DC Connections To make the last DC connectionsPowering Up To make the last AC connectionsTo install a BTS Installing Optional AccessoriesBattery Temperature Sensor Drip Protection Rubber Boots To install rubber bootsConfiguring the XC Series To configure the battery bank typeTo configure the charging type Operation About Charging Multiplex 3-Stage ChargingCharging Overview To force a battery detection sequenceSequential 2-Stage Charging Temperature Considerations Disqualified BatteriesThings to be aware Perform these disqualification checks in the order shownCharging Batteries To charge your batteriesCharging Batteries Equalizing Flooded Batteries About EqualizingPerforming An Equalization To equalize your batteriesThere are two ways to turn the XC Series on Transitioning the XC Series to On, Disabled or OffThere are two ways to disable the XC Series There is only one way to safely turn the XC Series offAccessing Charger Information Reading Remote Display and Onboard Status Indicator LightsABS Cerr Reporting While Charging or EqualizingTo view the present status of the banks Reporting While Battery MonitoringReporting While Disabled Using a Generator As Source Power Page Troubleshooting Care and Maintenance To clean battery terminalsIndicator Light Flashing Sequences 1Indicator Light Sequences on the XC SeriesError Messages on Remote Display 2Error MessagesErr Bat Problem Solving SymptomFault indicator light flashes. XC Series stops functioning Rdy Page Specifications Physical Specifications Electrical SpecificationsAC Input Specifications AC Input SpecificationsTemperature Specifications Protection FeaturesApprovals EMCPage Warranty and Product Information Limited Warranty forDisclaimer of Warranty Return Material Authorization Policy Information About Your System Page Xantrex Technology Inc