DeWalt DC310 Installing and Removing Battery Pack, Operation, Switch, Changing Blades, DC300 only

Page 11

CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

Installing and Removing the

Battery Pack (Fig. 2, 3)

NOTE: Make sure your battery pack is fully charged.

WARNING: Make certain the switch lock-off button (A) is engaged to prevent switch actuation before removing or installing battery.

To install the battery pack into the tool handle, align the base of the tool with the rails inside the tool’s handle and slide the battery pack firmly into the handle until you hear the lock snap into place.

FIG. 2

FIG. 3

A

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

To remove the battery pack from the tool, press the release button (N) and firmly pull the battery pack out of the tool handle. Insert it into the charger as described in the charger section of this manual.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before making any adjustments or removing/installing attachments or accessories.

Switch

Release switch lock-off button (A) by pressing button as shown (Fig. 3). Pull the trigger switch (B) to turn the motor ON. Releasing the trigger switch turns the motor OFF. Releasing the trigger switch also automatically actuates lock-off button.

NOTE: This tool has no provision to lock the switch in the ON position, and should never be locked ON by any other means.

Changing Blades

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before making any adjustments or removing/installing attachments or accessories.

DC300 ONLY (FIG. 4, 5)

The DC300 is equipped with a keyless blade clamp (H) and is designed to be tightened by hand. The use of external tools may cause damage to this blade clamp.

FIG. 4

M

FIG. 5

LOOSEN (clockwise)

 

L

 

 

O

P

TIGHTEN

(counterclockwise)

H

G F

English

10

Image 11
Contents Guide Dutilisation Manual DE Instrucciones DC310, 28 Volt 3800 RPM DC300, 36 Volt 4000 RPMPersonal Safety General Safety RulesWork Area Safety Electrical SafetyBattery Tool USE and Care Power Tool USE and CareCauses and Operator Prevention of Kickback Additional Safety Rules for Circular SawsService English Important Safety Instructions for Battery Chargers Read ALL Instructions Important Safety Instruction for Battery PacksIntroduction Charger Charging ProcedureRbrc Seal Storage RecommendationsImportant Charging Notes Charger DiagnosticsChanging Blades Installing and Removing Battery PackSwitch OperationTo Replace the Blade Fig To Install the BladeDC310 only To Install the Blade Loosen Lower Blade Guard DC300 and DC310Blades Cutting Depth AdjustmentBevel Angle Adjustment Fig Bevel Detent DC300 only Shoe Adjustment for 90˚ CutsKerf Indicator If Additional Adjustment is Needed FIGRipping FIG Workpiece SupportCutting Lubrication MaintenanceCleaning Charger Cleaning InstructionsDAY Money Back Guarantee Accessories Three Year Limited WarrantyYear Free Service Years Free Service on Dewalt Battery PacksPatent Notification DC310, 28 Volt DC300, 36 Volt 4000 tr/minSécurité Électricité Règles de sécurité GénéralitésConserver CES Directives Sécurité Aire DE TravailUtilisation ET Entretien DES Outils Électriques Utilisation ET Entretien DE Loutil Alimenté PAR Pile Règles de sécurité supplémentaires pour scies circulairesCauses DU Rebond ET Mesures Préventives Avertissement Toujours porter des lunettes de sécurité Minutes Lire Toutes LES Directives Directives de sécurité importantes pour les blocs-pilesProcédure de charge Recommandations de rangementLe sceau Srprctm ChargeurRemarques de chargement importantes Diagnostique de chargeurChangement de lames Installation et retrait du bloc-pilesFonctionnement GâchetteDC300 Seulement Installation de la lameRemplacement de la lame Fig DC310 Seulement PROTÈGE-LAME Inférieur DC300 ET DC310 LamesRéglage de l’angle de biseau Fig Réglage de la profondeur de coupeRéglage DE LA Scie Pour UNE Coupe EN Biseau Crans de biseau DC300 onlyRéglage de la semelle pour les coupes de Indicateur de trait de scieCoupe Support de la pièceDécoupe EN Poche FIG EntretienSciage EN Long FIG Garantie limitée de trois ans AccessoriesNettoyage LubrificationAvis de brevet Español Seguridad Eléctrica Reglas de seguridad generalesGuarde Estas Instrucciones Seguridad EN EL Área DE TrabajoUSO Y Cuidado DE LA Máquina Herramienta Servicio Normas de seguridad adicionales para las sierra circularesUSO Y Cuidado DE LA Herramienta a Batería Causas Y Prevención DE Rebote POR Parte DEL Operador VoltiosA............. amperios Hertz Vatios Por minuto LEA Todas LAS Instrucciones Conserve Estas Instrucciones IntroducciónProcedimiento de carga El sello RbrcRecomendaciones para el almacenamiento CargadorNotas importantes sobre la carga Diagnósticos del cargadorFuncionamiento Instalación y extracción del paquete de bateríasPara instalar la hoja InterruptorCambio de las hojas DC300 SolamenteDC310 Solamente Para reemplazar la hoja FigProtector Inferior DE LA Hoja DC300 y DC310 Para cambiar la hoja FigAjuste de la profundidad de corte HojasAjuste de la zapata para cortes a 90˚ Para Configurar LA Sierra Para UN Corte BiseladAjuste del ángulo del bisel Fig Retén del bisel DC300 solamenteCorte Indicador de corteApoyo de las piezas de trabajo Corte Interno FIG Corte Longitudinal FIGReparaciones MantenimientoLimpieza LubricaciónAÑO DE Servicio Gratuito Póliza de GarantíaGarantía limitada por tres años ExcepcionesCULIACAN, SIN Especificaciones Notificación de patentePage Page Cat Number Voltage