DeWalt DC9000, DC9360, DC9280, DC310 Cutting Depth Adjustment, Blades, Bevel Angle Adjustment Fig

Page 14
FIG. 10

English

protect you under all circumstances. Your safety depends on following all warnings and precautions as well as proper operation of the saw. Check lower guard for proper closing before each use as outlined in Additional Safety Rules for Circular Saws. If the lower blade guard is missing or not working properly, have the saw serviced before using. To assure product safety and reliability, repair, maintenance and adjustment should be performed by an authorized service center or other qualified service organization, always using

Cutting Depth

Adjustment

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before making any adjustments or removing/installing attachments or accessories.

FIG. 9

D

identical replacement parts.

Blades

WARNING: To minimize the risk of eye injury, always use eye protection. Carbide is a hard but brittle material. Foreign objects in the workpiece such as wire or nails can cause tips to crack or break. Only operate saw when proper saw blade guard is in place. Mount blade securely in proper rotation before using, and always use a clean, sharp blade.

CAUTION: Do not cut ferrous metals (steel), masonry, glass, Hardiplank® (or similar masonry-type planking), cement board or tile with this saw.

Do not use abrasive wheels or blades. A dull blade will cause slow, inefficient cutting, overload on the saw motor, excessive splintering, and could increase the possibility of kickback. Please refer to the following table to determine the correct size replacement blade for your model saw.

Model Diameter Arbor

DC300 7-1/4" 5/8"

DC310 6-1/2" 5/8"

Use only DEWALT general purpose cutting, smooth wood cutting, or non-carbide plywood/vinyl cutting blades.

If you need assistance regarding blades, please call 1-800-4- DEWALT (1-800-433-9258).

1.Hold the saw firmly and loosen

(clockwise) the depth adjustment lever (Fig. 9, D) and move shoe to obtain the desired depth of cut.

2.Make sure the depth adjustment lever has been retightened (counterclockwise) before operating saw.

For the most efficient cutting action,

set the depth adjustment so that one tooth of the blade will project below the material to be cut. This distance is from

the tip of the tooth to the bottom of the gullet in front of it. This keeps blade friction at a minimum, removes sawdust from the cut, results in cooler, faster sawing and reduces the chance of kickback. A method for checking for correct cutting depth is shown in Figure 10. Lay a piece of the material

you plan to cut along the side of the blade, as shown, and observe how much tooth projects beyond the material.

NOTE: When using carbide-tipped blades, make an exception to the above rule and allow only one-half of a tooth to project below the material to be cut.

Bevel Angle Adjustment (Fig. 11)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before

13

Image 14
Contents Guide Dutilisation Manual DE Instrucciones DC300, 36 Volt 4000 RPM DC310, 28 Volt 3800 RPMElectrical Safety General Safety RulesWork Area Safety Personal SafetyPower Tool USE and Care Battery Tool USE and CareCauses and Operator Prevention of Kickback Additional Safety Rules for Circular SawsService English Important Safety Instructions for Battery Chargers Read ALL Instructions Important Safety Instruction for Battery PacksIntroduction Storage Recommendations Charging ProcedureRbrc Seal ChargerCharger Diagnostics Important Charging NotesOperation Installing and Removing Battery PackSwitch Changing BladesTo Replace the Blade Fig To Install the BladeDC310 only To Install the Blade Lower Blade Guard DC300 and DC310 LoosenBlades Cutting Depth AdjustmentBevel Angle Adjustment Fig If Additional Adjustment is Needed FIG Shoe Adjustment for 90˚ CutsKerf Indicator Bevel Detent DC300 onlyRipping FIG Workpiece SupportCutting Charger Cleaning Instructions MaintenanceCleaning LubricationYears Free Service on Dewalt Battery Packs Accessories Three Year Limited WarrantyYear Free Service DAY Money Back GuaranteePatent Notification DC300, 36 Volt 4000 tr/min DC310, 28 VoltSécurité Aire DE Travail Règles de sécurité GénéralitésConserver CES Directives Sécurité ÉlectricitéUtilisation ET Entretien DES Outils Électriques Règles de sécurité supplémentaires pour scies circulaires Utilisation ET Entretien DE Loutil Alimenté PAR PileCauses DU Rebond ET Mesures Préventives Avertissement Toujours porter des lunettes de sécurité Minutes Directives de sécurité importantes pour les blocs-piles Lire Toutes LES DirectivesChargeur Recommandations de rangementLe sceau Srprctm Procédure de chargeDiagnostique de chargeur Remarques de chargement importantesGâchette Installation et retrait du bloc-pilesFonctionnement Changement de lamesDC300 Seulement Installation de la lameRemplacement de la lame Fig DC310 Seulement Lames PROTÈGE-LAME Inférieur DC300 ET DC310Réglage de la profondeur de coupe Réglage de l’angle de biseau FigIndicateur de trait de scie Crans de biseau DC300 onlyRéglage de la semelle pour les coupes de Réglage DE LA Scie Pour UNE Coupe EN BiseauSupport de la pièce CoupeDécoupe EN Poche FIG EntretienSciage EN Long FIG Lubrification AccessoriesNettoyage Garantie limitée de trois ansAvis de brevet Español Seguridad EN EL Área DE Trabajo Reglas de seguridad generalesGuarde Estas Instrucciones Seguridad EléctricaUSO Y Cuidado DE LA Máquina Herramienta Servicio Normas de seguridad adicionales para las sierra circularesUSO Y Cuidado DE LA Herramienta a Batería Causas Y Prevención DE Rebote POR Parte DEL Operador VoltiosA............. amperios Hertz Vatios Por minuto Conserve Estas Instrucciones Introducción LEA Todas LAS InstruccionesCargador El sello RbrcRecomendaciones para el almacenamiento Procedimiento de cargaDiagnósticos del cargador Notas importantes sobre la cargaInstalación y extracción del paquete de baterías FuncionamientoDC300 Solamente InterruptorCambio de las hojas Para instalar la hojaPara reemplazar la hoja Fig DC310 SolamentePara cambiar la hoja Fig Protector Inferior DE LA Hoja DC300 y DC310Hojas Ajuste de la profundidad de corteRetén del bisel DC300 solamente Para Configurar LA Sierra Para UN Corte BiseladAjuste del ángulo del bisel Fig Ajuste de la zapata para cortes a 90˚Corte Indicador de corteApoyo de las piezas de trabajo Corte Longitudinal FIG Corte Interno FIGLubricación MantenimientoLimpieza ReparacionesExcepciones Póliza de GarantíaGarantía limitada por tres años AÑO DE Servicio GratuitoCULIACAN, SIN Notificación de patente EspecificacionesPage Page Cat Number Voltage