Hitachi NR83A2(Y) manual Adjusting AIR Pressure, Nailer Must not Leak AIR, Nailer Must not Operate

Page 11

Do not load any nails in the Nailer.

Set the switching device to the leftward position

(SINGLE SEQUENTIAL ACTUATION MECHANISM). (Set the switching device to the leftward position completely as shown in the diagram. Otherwise, it will not operate properly.)

Leftward position

Switching device

☐THE NAILER MUST NOT LEAK AIR.

(3)Remove the finger from the trigger and press the push lever against the wood.

☐THE NAILER MUST NOT OPERATE.

Do not pull Trigger

Depress Push Lever

(4)Separate the push lever from the wood.

Next, point the nailer downward, pull the trigger and then wait in that position for 5 seconds or longer.

☐ THE NAILER MUST NOT OPERATE.

English

2Hold the trigger back while separating the push lever from the wood.

☐The nailer will remain in operated status (the driver blade will remain at the bottom).

3Remove the finger from the trigger.

☐Nailer operation will end (the driver blade will return to the top).

(6)Set the switching device to the rightward position

(CONTACT ACTUATION MECHANISM).

(Set the switching device to the rightward position completely as shown in the diagram. Otherwise, it will not operate properly.)

Rightward position

Switching device

With the Nailer off the workpiece, pull the trigger. Depress the push lever against the workpiece.

☐THE NAILER MUST OPERATE.

(7)If no abnormal operation is observed, you may load nails in the Nailer.

Drive nails into the workpiece that is the same type to be used in the actual application.

☐THE NAILER MUST OPERATE PROPERLY.

ADJUSTING AIR PRESSURE

WARNING

Pull Trigger

(5)1 Without touching the trigger, depress the push lever against the workpiece.

Pull the trigger.

☐THE NAILER MUST OPERATE.

⬤ Do not exceed 120 psi (8.3 bar 8.5 kgf/cm2).

Adjust the air pressure at recommended operating pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm2) according to the length of nails and the hardness of workpiece.

The correct air pressure is the lowest pressure which will do the job. Using the Nailer at a higher than required air pressure unnecessarily over stresses the Nailer.

— 11 —

Image 11

Contents Peligro NR 83A2 Y NR83A2 S1Contents Contact Actuation Mechanism Important Safety InformationSingle Sequential Actuation Mechanism Always Wear EAR and Head Protection SafetyNever Point Tool AT Yourself or Others in Work Area Choice of Triggering Method is ImportantNever USE in Presence of Flammable Liquids or Gases Keep Work Area CleanCheck for Live Wires Store Nailer ProperlyEMPLOYER’S Responsibilities Actuation Mechanism OperationName of Parts Single Sequential Contact ActuationNail Selection SpecificationsAccessories Standard AccessoriesWorking Environment Optional AccessoriesApplications Before OperationAir consumption Testing the NailerLubrication Cold Weather CareNailer Must Operate Adjusting AIR PressureNailer Must not Leak AIR Nailer Must not OperateNailer Operation Loading NailsMechanism Methods of OperationPreviously pull the trigger Trigger Push Lever Always Wear EYE Protection Adjusting the Nailing DepthDisconnect AIR Hose from Nailer Inspecting the magazine MaintenanceMaintenance and Inspection Service and RepairsProblem Check Method Correction Action WHY HOWMécanisme DE Déclenchement Séquentiel Unique Definition DES Mots DE SignalisationInformation Importante DE Sécurité Explication DE L’ACTION DE Clouage DU Cloueur HitachiAvertissement SecuriteEloigner LES Visiteurs Toujours Porter DES Protections ANTI- Bruit ET UN CasqueRanger LE Cloueur Correctement Maintenir L’AIRE DE Travail PropreManipuler LE Cloueur Correctement Verifier S’IL Y a DES Fils Sous TensionDebrancher LE Tuyau D’AIR DU Cloueur Quand Rester SUR SES GardesLunettes DE Protection Responsabilites DE L’EMPLOYEURNOM DES Pieces UtilisationSelection DES Clous Avertissement Accessoires AvertissementAccessoires Standard Alimentation D’AIR Accessoires EN OptionAvant L’UTILISATION Environnement DE Travail AvertissementConsommation d’air GraissageEntretien PAR Temps Froid Essai DU CloueurLE Cloueur Doit Fonctionner Réglage DE LA Pression D’AIR AvertissementLE Cloueur NE Doit PAS Avoir DE Fuite D’AIR LE Cloueur NE Doit PAS FonctionnerUtilisation DU Cloueur Chargement DES Clous AvertissementTirer sur la gâchette rapidement et fermement Méthodes D’UTILISATIONAvertissement Debrancher LE Tuyau D’AIR DU Cloueur Réglage DE LA Profondeur DE ClouageToujours Porter DES Lunettes DE Protection Inspection du magasin EntretienEntretien ET Inspection Entretien ET Reparations AvertissementAction Pourquoi Comment Probleme Verification CorrectionLesiones DE Gravedad Información Importante Sobre SeguridadDefinición DE LAS Palabras Clave Explicación LA Acción DE Clavado DEL Clavador HitachiES Importante LA Elección DE Método DE Activación SeguridadAdvertencia Mantenga a LOS Visitantes Alejados Utilice Siempre Protectores Para LOS Oídos Y LA CabezaGuarde Adecuadamente EL Clavador Mantenga EL Área DE Trabajo LimpiaManeje Correctamente EL Clavador Compruebe SI HAY Cables ActivosDesconecte LA Manguera DE Aire DEL Clavador Cuando Permanezca AlertaGafas Protectoras Para LOS Ojos Responsabilidades DEL EmpresarioMecanismo DE OperaciónNomenclatura Accesorios Estándar EspecificacionesSelección DE Clavos Advertencia Accesorios AdvertenciaEntorno DE Trabajo Advertencia Accesorios OpcionalesAplicaciones Antes DE LA OperaciónPrueba DEL Clavador Peligro LubricaciónCuidados Para Climas Fríos PrecauciónEL Clavador Deberá Funcionar LA Palanca DE Empuje Deberá Poder Accionarse SIN DificultadEL Clavador no Deberá Funcionar EL Clavador no Deberá Tener Fugas DE Aire EL Martillo Automático Deberá Funcionar Adecuadamente Ajuste DE LA Presión DE Aire AdvertenciaCarga DE Clavos Advertencia Métodos DE Operación Operación DEL ClavadorAdvertencia Utilice Siempre Gafas Protectoras Para LOS Ojos Ajuste DE LA Profundidad DE ClavadoDesconecte LA Manguera DE Aire DEL Clavador Inspección del cargador MantenimientoMantenimiento E Inspección Servicio Y Reparaciones AdvertenciaAcción Para Cómo Problema Método DE Comprobación SoluciónStrip Nailer Parts Name Plate For Model Y, S1 887-903 Standard Accessories Code no Description Kestrel Road Mississauga on L5T 1Z5 Steve Reynolds Blvd Norcross, GA