Hitachi NR83A2(Y), NR83A2(S1) Important Safety Information, Single Sequential Actuation Mechanism

Page 3

English

IMPORTANT SAFETY INFORMATION

Read and understand tool labels and all of the operating instructions, safety precautions and warnings in this manual before operating or maintaining this nailer. Failure to follow warnings could result in DEATH or SERIOUS INJURY.

Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by DANGERS and WARNINGS on the Nailer and in this Manual.

Never use this Nailer for applications other than those specified in this Manual.

DEFINITIONS OF SIGNAL WORDS

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER

◯SINGLE SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull the trigger to drive the nail. First, pull the trigger; next, press the push lever against the wood to drive the nail.

After nailing once, nailing will not be possible again until the trigger is released and pressed again.

◯CONTACT ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull the trigger to drive the nail. First, pull the trigger; next, press the push lever against the wood to drive the nail.

If the trigger is held back, a nail will be driven each time the push lever is pressed against the wood.

— 3 —

Image 3

Contents Peligro NR 83A2 Y NR83A2 S1Contents Important Safety Information Single Sequential Actuation MechanismContact Actuation Mechanism Always Wear EAR and Head Protection SafetyNever Point Tool AT Yourself or Others in Work Area Choice of Triggering Method is ImportantNever USE in Presence of Flammable Liquids or Gases Keep Work Area CleanCheck for Live Wires Store Nailer ProperlyEMPLOYER’S Responsibilities Actuation Mechanism OperationName of Parts Single Sequential Contact ActuationNail Selection SpecificationsAccessories Standard AccessoriesWorking Environment Optional AccessoriesApplications Before OperationAir consumption Testing the NailerLubrication Cold Weather CareNailer Must Operate Adjusting AIR PressureNailer Must not Leak AIR Nailer Must not OperateNailer Operation Loading NailsMechanism Methods of OperationPreviously pull the trigger Trigger Push Lever Adjusting the Nailing Depth Disconnect AIR Hose from NailerAlways Wear EYE Protection Inspecting the magazine MaintenanceMaintenance and Inspection Service and RepairsProblem Check Method Correction Action WHY HOWMécanisme DE Déclenchement Séquentiel Unique Definition DES Mots DE SignalisationInformation Importante DE Sécurité Explication DE L’ACTION DE Clouage DU Cloueur HitachiAvertissement SecuriteEloigner LES Visiteurs Toujours Porter DES Protections ANTI- Bruit ET UN CasqueRanger LE Cloueur Correctement Maintenir L’AIRE DE Travail PropreManipuler LE Cloueur Correctement Verifier S’IL Y a DES Fils Sous TensionDebrancher LE Tuyau D’AIR DU Cloueur Quand Rester SUR SES GardesLunettes DE Protection Responsabilites DE L’EMPLOYEURNOM DES Pieces UtilisationAccessoires Avertissement Accessoires StandardSelection DES Clous Avertissement Alimentation D’AIR Accessoires EN OptionAvant L’UTILISATION Environnement DE Travail AvertissementConsommation d’air GraissageEntretien PAR Temps Froid Essai DU CloueurLE Cloueur Doit Fonctionner Réglage DE LA Pression D’AIR AvertissementLE Cloueur NE Doit PAS Avoir DE Fuite D’AIR LE Cloueur NE Doit PAS FonctionnerUtilisation DU Cloueur Chargement DES Clous AvertissementTirer sur la gâchette rapidement et fermement Méthodes D’UTILISATIONAvertissement Réglage DE LA Profondeur DE Clouage Toujours Porter DES Lunettes DE ProtectionDebrancher LE Tuyau D’AIR DU Cloueur Inspection du magasin EntretienEntretien ET Inspection Entretien ET Reparations AvertissementAction Pourquoi Comment Probleme Verification CorrectionLesiones DE Gravedad Información Importante Sobre SeguridadDefinición DE LAS Palabras Clave Explicación LA Acción DE Clavado DEL Clavador HitachiSeguridad AdvertenciaES Importante LA Elección DE Método DE Activación Mantenga a LOS Visitantes Alejados Utilice Siempre Protectores Para LOS Oídos Y LA CabezaGuarde Adecuadamente EL Clavador Mantenga EL Área DE Trabajo LimpiaManeje Correctamente EL Clavador Compruebe SI HAY Cables ActivosDesconecte LA Manguera DE Aire DEL Clavador Cuando Permanezca AlertaGafas Protectoras Para LOS Ojos Responsabilidades DEL EmpresarioOperación NomenclaturaMecanismo DE Accesorios Estándar EspecificacionesSelección DE Clavos Advertencia Accesorios AdvertenciaEntorno DE Trabajo Advertencia Accesorios OpcionalesAplicaciones Antes DE LA OperaciónPrueba DEL Clavador Peligro LubricaciónCuidados Para Climas Fríos PrecauciónEL Clavador Deberá Funcionar LA Palanca DE Empuje Deberá Poder Accionarse SIN DificultadEL Clavador no Deberá Funcionar EL Clavador no Deberá Tener Fugas DE AireAjuste DE LA Presión DE Aire Advertencia Carga DE Clavos Advertencia EL Martillo Automático Deberá Funcionar Adecuadamente Métodos DE Operación Operación DEL ClavadorAdvertencia Ajuste DE LA Profundidad DE Clavado Desconecte LA Manguera DE Aire DEL ClavadorUtilice Siempre Gafas Protectoras Para LOS Ojos Inspección del cargador MantenimientoMantenimiento E Inspección Servicio Y Reparaciones AdvertenciaAcción Para Cómo Problema Método DE Comprobación SoluciónStrip Nailer Parts Name Plate For Model Y, S1 887-903 Standard Accessories Code no Description Kestrel Road Mississauga on L5T 1Z5 Steve Reynolds Blvd Norcross, GA