Hitachi Complete Maintenance Instructions and Repair Manual for Nail Guns
Page 16

English

MAINTENANCE

NOTE: The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer. Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer.

MAINTENANCE AND INSPECTION

Read section titled “SAFETY” (pages 4 – 6).

WARNING

⬤Disconnect air hose and remove all nails from Nailer when:

1)doing maintenance and inspection; and

2)clearing a jam.

1.Inspecting the magazine

1DISCONNECT AIR HOSE.

2Clean the magazine. Remove plastic tips or wooden tips which may have accumulated in the magazine. Lubricate it with Hitachi pneumatic tool lubricant.

 

1

 

Disconnect

Nail Feeder

air hose

 

Magazine

CAUTION

⬤Check that the nail feeder slides smoothly by pulling it with finger.

If not smooth, nails can be driven at an irregular angle and hurt someone.

2. Storing

◯When not in use for an extended period, apply a thin coat of the lubricant to the steel parts to avoid rust.

◯Do not store the Nailer in a cold weather environment. Keep the Nailer in a warm area.

◯When not in use, the Nailer should be stored in a warm and dry place.

Keep out of reach children.

3. WARNING LABEL

Change the WARNING LABEL if missing or damaged. A new WARNING LABEL is available from a Hitachi authorized service center.

Warning

Label

4.Maintenance chart (See page 17)

5.Operator troubleshooting (See page 17)

6.Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION

⬤Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

SERVICE AND REPAIRS

WARNING

⬤Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer.

⬤Use only parts supplied or recommended by Hitachi for repair.

All quality Nailers will eventually require servicing or replacement of parts because of wear from normal use.

NOTE: Specifications are subject to change without any obligation on the part of HITACHI.

— 16 —

Page 15 Page 17
Image 16
Page 15 Page 17
Contents NR 83A2 Y NR83A2 S1 PeligroContents Single Sequential Actuation Mechanism Important Safety InformationContact Actuation Mechanism Safety Never Point Tool AT Yourself or Others in Work AreaChoice of Triggering Method is Important Always Wear EAR and Head ProtectionKeep Work Area Clean Check for Live WiresStore Nailer Properly Never USE in Presence of Flammable Liquids or GasesEMPLOYER’S Responsibilities Operation Name of PartsSingle Sequential Contact Actuation Actuation MechanismSpecifications AccessoriesStandard Accessories Nail SelectionOptional Accessories ApplicationsBefore Operation Working EnvironmentTesting the Nailer LubricationCold Weather Care Air consumptionAdjusting AIR Pressure Nailer Must not Leak AIRNailer Must not Operate Nailer Must OperateLoading Nails Nailer OperationMethods of Operation MechanismPreviously pull the trigger Trigger Push Lever Disconnect AIR Hose from Nailer Adjusting the Nailing DepthAlways Wear EYE Protection Maintenance Maintenance and InspectionService and Repairs Inspecting the magazineAction WHY HOW Problem Check Method CorrectionDefinition DES Mots DE Signalisation Information Importante DE SécuritéExplication DE L’ACTION DE Clouage DU Cloueur Hitachi Mécanisme DE Déclenchement Séquentiel UniqueSecurite AvertissementToujours Porter DES Protections ANTI- Bruit ET UN Casque Ranger LE Cloueur CorrectementMaintenir L’AIRE DE Travail Propre Eloigner LES VisiteursVerifier S’IL Y a DES Fils Sous Tension Debrancher LE Tuyau D’AIR DU Cloueur QuandRester SUR SES Gardes Manipuler LE Cloueur CorrectementResponsabilites DE L’EMPLOYEUR Lunettes DE ProtectionUtilisation NOM DES PiecesAccessoires Standard Accessoires AvertissementSelection DES Clous Avertissement Accessoires EN Option Avant L’UTILISATIONEnvironnement DE Travail Avertissement Alimentation D’AIRGraissage Entretien PAR Temps FroidEssai DU Cloueur Consommation d’airRéglage DE LA Pression D’AIR Avertissement LE Cloueur NE Doit PAS Avoir DE Fuite D’AIRLE Cloueur NE Doit PAS Fonctionner LE Cloueur Doit FonctionnerChargement DES Clous Avertissement Utilisation DU CloueurMéthodes D’UTILISATION Tirer sur la gâchette rapidement et fermementAvertissement Toujours Porter DES Lunettes DE Protection Réglage DE LA Profondeur DE ClouageDebrancher LE Tuyau D’AIR DU Cloueur Entretien Entretien ET InspectionEntretien ET Reparations Avertissement Inspection du magasinProbleme Verification Correction Action Pourquoi CommentInformación Importante Sobre Seguridad Definición DE LAS Palabras ClaveExplicación LA Acción DE Clavado DEL Clavador Hitachi Lesiones DE GravedadAdvertencia SeguridadES Importante LA Elección DE Método DE Activación Utilice Siempre Protectores Para LOS Oídos Y LA Cabeza Guarde Adecuadamente EL ClavadorMantenga EL Área DE Trabajo Limpia Mantenga a LOS Visitantes AlejadosCompruebe SI HAY Cables Activos Desconecte LA Manguera DE Aire DEL Clavador CuandoPermanezca Alerta Maneje Correctamente EL ClavadorResponsabilidades DEL Empresario Gafas Protectoras Para LOS OjosNomenclatura OperaciónMecanismo DE Especificaciones Selección DE Clavos AdvertenciaAccesorios Advertencia Accesorios EstándarAccesorios Opcionales AplicacionesAntes DE LA Operación Entorno DE Trabajo AdvertenciaLubricación Cuidados Para Climas FríosPrecaución Prueba DEL Clavador PeligroLA Palanca DE Empuje Deberá Poder Accionarse SIN Dificultad EL Clavador no Deberá FuncionarEL Clavador no Deberá Tener Fugas DE Aire EL Clavador Deberá FuncionarCarga DE Clavos Advertencia Ajuste DE LA Presión DE Aire Advertencia EL Martillo Automático Deberá Funcionar Adecuadamente Operación DEL Clavador Métodos DE OperaciónAdvertencia Desconecte LA Manguera DE Aire DEL Clavador Ajuste DE LA Profundidad DE ClavadoUtilice Siempre Gafas Protectoras Para LOS Ojos Mantenimiento Mantenimiento E InspecciónServicio Y Reparaciones Advertencia Inspección del cargadorProblema Método DE Comprobación Solución Acción Para CómoStrip Nailer Parts Name Plate For Model Y, S1 887-903 Standard Accessories Code no Description Steve Reynolds Blvd Norcross, GA Kestrel Road Mississauga on L5T 1Z5
Top Page Image Contents