DeWalt DW079 instruction manual Using Automatic Tune-Up Mode, Chargers, Charging Procedure

Page 8

English

•Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized service center.

•Do not disassemble charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

•Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

•NEVER attempt to connect 2 chargers together.

•The charger is designed to operate on standard 120V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.

Using Automatic Tune-Up™ Mode

The Automatic Tune-Up™ Mode equalizes or balances the individual cells in the battery pack allowing it to function at peak capacity. Battery packs should be tuned up weekly or after 10 charge/discharge cycles or whenever the pack no longer delivers the same amount of work. To use the Automatic Tune- Up™, place the battery pack in the charger and leave it for at least 8 hours. The charger will cycle through the following modes.

1.The red light will blink continuously indicating that the 1-hour charge cycle has started.

2.When the 1-hour charge cycle is complete, the light will stay on continuously and will no longer blink. This indicates that the pack is fully charged and can be used at this time.

3.If the pack is left in the charger after the initial 1-hour charge, the charger will begin the Automatic Tune-Up™ mode. This mode continues up to 8 hours or until the individual cells in the battery pack are equalized. The battery pack is ready for use and can be removed at any time during the Automatic Tune- Up™ mode.

6

4.Once the Automatic Tune Up™ mode is complete, the charger will begin a maintenance charge; the red indicator will remain lit.

Chargers

Your tool uses a DEWALT 9.6, 12, 14.4, 18 Volt charger. Be sure to read all safety instructions before using your charger. Consult the chart at the end of this manual for compatibility of chargers and battery packs.

Charging Procedure

DANGER: Electrocution hazard. 120 volts present at charging terminals. Do not probe with conductive objects. Danger of electric shock or electrocution.

1.Plug the charger into an appropriate outlet before inserting battery pack.

2.Insert the battery pack into the charger, making sure the pack is fully seated. The red (charging) light will blink continuously indicating that the charging process has started.

3.The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger.

Indicator Light Operation

Page 7 Page 9
Image 8
Page 7 Page 9
Contents DW079 Rotary Laser Laser rotatif Láser rotativo Page Safety Instructions for Lasers Laser Information Important Safety Instructions for All Battery Packs Read ALL InstructionsRbrc Seal Important Safety Instructions for All Battery ChargersSpecific Safety Instructions for Lithium ION LI-ION Wire Size AWG Do not operate charger with damaged cord or plugUsing Automatic Tune-Up Mode Charging ProcedureIndicator Light Operation ChargersCharge Indicators HOT/COLD Pack DelayProblem Power Line Leaving the Battery Pack in the ChargerFor Future USE Laser Operation Laser MaintenanceStorage Recommendations Laser Control Panel Buttons Installing and Removing Battery Pack FigLaser Control Panel Self-Leveling Horizontal Mode Self-Leveling Vertical ModeManual Mode Using Scan ModeUsing the Wireless Remote Control Fig Using Manual Slope Mode Entering and exiting Manual Slope ModeSetting the Slope Direction Setting the Amount of SlopeRemote Control SPEED/ROTATION Button Remote Control Scan Mode ButtonRemote Control Public and Private Mode Height of Instrument AlertLaser Troubleshooting Using the Laser on a TripodUsing the Laser on a Floor Fig Manual Head RotationLaser Accessories Laser Enhancement GlassesDigital Laser Detector DW0772 Fig Target CardDetector Controls FIG Detector Operation FigBatteries FIG Detector Cleaning and Storage Detector ServiceDetector Troubleshooting Mounting on a Grade ROD FIGUsing the Laser with a Wall Mount Construction Grade RodDETECTOR’S Speaker Makes no Sound Detector does not Respond to a Stationary Laser BeamLaser Maintenance FIG MarkField Calibration Check Level Calibration Check X-AXISThree Year Limited Warranty RepairsEnglish Conserver CES Directives Consignes de sécurité pour les lasersInformations relatives au laser Lire Toutes LES Directives Caractéristiques TechniquesFrançais Le sceau Srprctm Calibre AWG Utilisation du Mode Tune-UpTMautomatique ChargeursProcédure de charge Fonctionnement des voyantsVoyants de charge Remarques importantes concernant le chargementFonction DE Suspension DU BLOC-PILES CHAUD/FROID Problèmes Avec LE SecteurRecommandations de rangement Installation et retrait du bloc-piles fig Installation DU BLOC-PILESPanneau de contrôle du laser Retrait DU BLOC-PILESEn Mode d’auto-nivelage horizontal En Mode d’auto-nivelage verticalEn Mode manuel Boutons du panneau de contrôle du laserUtilisation du Mode de balayage Mode publicPour activer le Mode public Mode privéUtilisation de la Télécommande Sans fil fig Mode ignorer télécommandePour activer le Mode ignorer télécommande Utilisation du Mode manuel d’inclinaisonParamétrage du taux d’inclinaison Télécommande Boutons FlècheParamétrage de la direction d’inclinaison Télécommande Mode Public ET Privé Télécommande Bouton VITESSE/ROTATIONTélécommande Bouton Mode DE Balayage Signal de changement de hauteur de l’appareil LE Laser ET LA Télécommande NE Sont PAS SynchronisésGuide de dépannage du laser Utilisation du laser sur le sol figAccessoires laser Rotation manuelle de la têteCarte de détection de faisceau Lunettes de visualisation laserCommandes DU Capteur FIG Piles FIGInstallation SUR UNE Tige Graduée FIG Fonctionnement du capteur figEntretien et rangement du capteur Réparation du capteurGuide de dépannage du capteur Tige graduée de constructionUtilisation du laser avec un montage mural fig SS MMVérification DE Calibrage AXE DES Maintenance DU LaserVérification du calibrage fig Vérification DE Calibrage AXE DES Y Vérification DE L’APLOMBRéparations Garantie limitée de trois ansContrat D’ENTRETIEN Gratuit D’UN AN Garantie DE Remboursement DE 90 JoursGuarde Estas Instrucciones Instrucciones de seguridad para láseresInformación sobre el láser LEA Todas LAS Instrucciones EspecificacionesEspañol El sello Rbrctm Tamaño de conductor AWG Utilización de la modalidad Tune-UpTMautomática CargadoresProcedimiento de carga Operación de la luz indicadora Indicadores de cargaLínea DE Alimentación Problemática Notas importantes sobre la cargaRetardo POR Unidad CALIENTE/FRÍA Permanencia DE LA Unidad DE Batería EN EL CargadorRecomendaciones de almacenamiento Panel de control del láser Cómo instalar y retirar la unidad de batería FigCómo Retirar LA Unidad DE Batería Cómo Instalar LA Unidad DE BateríaBotones del panel de control del láser En la modalidad de autonivelado horizontalEn la modalidad de autonivelado vertical En la modalidad manualModalidades PÚBLICA, Privada Y SIN Remoto Modalidad públicaPara activar la modalidad pública Modalidad privadaUso del control remoto inalámbrico Modalidad sin control remotoPara activar la modalidad sin control remoto Uso de la modalidad de inclinación manualControl Remoto Botones DE Flecha Para configurar la dirección de inclinaciónConfiguración del grado de inclinación Control Remoto Modalidad Pública Y Privada Control Remoto Botón DE VELOCIDAD/ROTACIÓNControl Remoto Botón DE Modalidad DE Escáner Resolución de problemas con el láser Para Reconfigurar LA Unidad Láser Para USO ContinuoAlerta por elevación del instrumento Uso del láser con un trípodeUso del láser directamente en el piso Fig Rotación manual del cabezalAccesorios para el láser Gafas láserControles DEL Detector FIG Detector digital de láser DW0772 FigPilas FIG Operación del detector Fig Montaje Sobre UNA Vara Graduada FIGServicio para el detector Resolución de problemas del detectorLimpieza y almacenamiento del detector EL Detector Emite UN Tono Pero LA Pantalla LCD no Funciona Vara graduada de construcciónUso del láser con un soporte de pared Mantenimiento DEL Láser Control de calibrado en el campo Control DE Calibrado DEL Nivel EJEControl DE Calibrado DEL Nivel EJE Y Control DE Error DE LA Plomada FIGReparaciones Póliza de Garantía Garantía limitada de tres añosExcepciones Servicio Gratuito DE 1 AÑOGarantía DE Reembolso DE Dinero DE 90 Días DW079 18,0 V DCPage Dewalt Battery and Charger Systems
Top Page Image Contents