Wolfcraft 6157 manual Using the Featherboard Flaps, Adjusting the Fence Slides, Unitized Fence

Page 21

OPTIONS / ACCESSORIES

Using the Featherboard Flaps

The featherboard flaps (P) provide support for your workpiece by holding the piece securely to help minimize chatter and kickback. Insert the featherboard flaps into the fences. See Figure 27.

P

Figure 27

5.Loosen the knobs on the fences, turn router ON and pass the board through the router bit to create an exact cut-out of your bit in the fence. If a larger

bit exposure is needed, notch the board out as needed.

Adjusting the Fence Slides

The fence slides can be positioned closer to the router bit to provide better support of the workpiece. To reposition the fence slides, loosen the wing nuts, reposition fence slides closer to the router bit and tighten wing nuts securely. DO NOT let the fence slides touch the router bit. See Figure 28.

Unitized Fence

A unitized fence can be created to make it possible to rout taller workpieces.

The router table is designed to accept a board (unitized fence) of up to 4 inches in height. To make a unitized fence, perform the following:

1.Obtain a straight board up to 4 inches in height.

2.Place the board against the fences and mark the location of the holes in the fences.

3.Drill and countersink the board to accommodate the hardware (not included) to attach the board to the fences.

4.Attach the board securely to the fences (hardware not included).

Figure 28

21

Image 21

Contents Wolfcraft Warranty Table of ContentsDress for Safety Safety InstructionsIntroduction Unpacking and Checking ContentsRouter Table features include Features and SpecificationsPackage Contents & Hardware Legend Package Contents & Hardware Legend Package Contents & Hardware Legend Attach Switch Box and Safety Shield AssemblyTools Required Assemble StandAssemble Fence and Miter Guide Groove Mounting Routers with 7 Round Adaptor Base Plate Mounting the RouterETS Securing the Router Table Switch BOXIntroduction Electrical HookupDo not Modify the Plug Switch Box Familiarization For Routers With LOCK-ON FeatureOperation of Switch Box and Router Circuit Breaker Table Flatness AdjustmentUsing the Fences Connecting a VacuumUsing the Router for Beading and Edge Cutting OperationUsing Ball-Bearing-Guided Bits Using the Router as a JointerCutting Without Fences and/or Guard Using the Featherboard Flaps Adjusting the Fence SlidesUnitized Fence Mounting a Dremel Rotary Hobby Tool Not Included Optional Floor Leg MountingRepair Parts 6157 Router Table KEY Description Índice Table DES MatieresConsignes DE Sécurité Déballer ET Vérifier LE Contenu Las características de la mesa para fresadora 6157 incluyen Voici les caractéristiques propres à la table à toupieDescription QTÉ Artículo Descripción Cant Base du guide gauche Base de barrera guía, izquierda Contenu DE Lemballage ET Légende DU Matériel suite Outils requis/Herramientas necesarias ASSEMBLAGE/ARMADOPUL PUS Encoche ranura Montage DE LA TOUPILLEUSE/CÓMO Montar LA Fresadora Asegúrese que los tornillos de la placa base Boîte DINTERRUPTEUR/CAJA DEL Interruptor Figura Utilisation de la boîte dinterrupteur et de la toupilleuse Toujours Disjoncteur/Interruptor automáticoUTILISATION/OPERACIÓN Para ayudarle a reducir la posibilidad de Petite pièce à travailler Morceau de récupération Guide monocoque Barrera guía unificada OPTIONS/OPCIONES / ACCESSOIRES/ACCESORIOSMonter un outil de bricolage rotatif Dremel non inclus SET CLÉ N Article Page Page Wolfcraft 6157 Wolfcraft