Black & Decker BDPS200 instruction manual Operation, Developing the Proper Sprayingtechnique

Page 9

FLOW CONTROL KNOB - (FIGURE G) FLOW CONTROL SETTINGS	G
The flow control knob regulates the amount of liquid that can be sprayed.
• Select low (1), medium (5) or high (9) on the flow control knob.
TIP: Always test the spray pattern on scrap cardboard or similar material
first. Begin with flow control knob on the highest flow setting. Heavier,
thicker materials should be sprayed on the higher setting closer to #9.
Thinner materials should be sprayed on the lower setting closer to #1.
OPERATION	H
ON / OFF TRIGGER - (FIGURE H)
The sprayer is turned on and off by the trigger.
• To turn the sprayer on, squeeze the trigger.

• To turn the sprayer off, release the trigger.

Never point the sprayer at any part of the body.

NeverWARNING:pull the triggerRiskwhileof injuryadjusting. the spray setting.

DEVELOPING THE PROPER SPRAYINGTECHNIQUE
• Practice spraying on a piece of scrap material such as cardboard to test your spray pattern and become familiar with
the speed settings flow control features of the sprayer.
• Ensure surface to be sprayed is free of dust, dirt, and grease.
• Ensure spray area is clean and free of dust that could be blown onto newly sprayed surfaces.
• Cover any areas not intended to be sprayed.
• Always spray from a minimum of 1 inch (25mm) to a maximum of 14 inches (355mm) (figure I). Optimal is usually
around 10 inches or use a paint stir stick as a reference.
• A commonly used method for spraying a large surface is the “crisscross” pattern. This is done by spraying in
horizontal strips and then crossing over these strips with vertical strips.
• To get an even spray distribution, always keep your arm at the same distance (figure I) from the surface you are
spraying and avoid moving your wrist (figure I1).	9

Image 9

Contents Power Paint Sprayer On/Off Switch Safety Guidelines Definitions Important Safety InstructionsTo avoid these risks, take the following preventions General Safety Warnings Grounding InstructionsTo avoid these risks,GENERALtake the. following preventions Volts Extension CordsFunctional Description ComponentsSET-UP Adjusting the FAN SpraynozzleSelecting the Proper Spray Nozzle Figures B and B1 Attachingthe SpraynozzlesLiquid Material Preparation Figures , E1 Common Dilution Rates on Paint canPreparation Tips Filling the Canister Figure FOperation Flow Control Knob Figure G Flow Control SettingsDeveloping the Proper Sprayingtechnique On / OFF Trigger Figure HFigure J3 To Begin CleaningFigure K3. Refer to figures C & C1 Reassembly Maintenance AccessoriesService Information Troubleshooting WarrantyProblem Possible Cause Possible Solution Prior to reassemblingMode DʼEMPLOI Table DES Matières Lignes directrices en matière de sécurité définitionsRisque Consignes DE Sécurité ImportantesRisque dʼexplosion DʼemploiInstructions DE Mise À LA Terre Avertissements DE Sécurité GénérauxJaunes Ne pas utiliser dʼadaptateur avec ce produitCalibre minimal des cordons de rallonge Description Fonctionnelle ComponentsPréparation Choix DE LA Buse DE Pulvérisation Adéquate Figures B ET B1Fixation DES Buses DE Pulvérisation Figures C ET C1 Peinture Taux DE Dilution Courants Indiqués SUR LE Contenant DEPréparation DU Produit Liquide Conseils DE PréparationMettre AU Point UNE Bonne Technique DE Pulvérisation Réglages DE DébitFonctionnement Horaire figure J3 NettoyagePour Amorcer LE Nettoyage Débrancher le pulvérisateur de la source dʼalimentationDéposer le piston et le ressort figure K7 Page Entretien AccessoiresInformation SUR LES Réparations Du pulvérisateurDépannage Problème Cause possible Solution possibleManual DE Instrucciones Interruptor de encendido/apagado ProvocardañosAVISO en la propiedad Instrucciones DE Seguridad ImportantesLea y comprenda el manual de instrucciones Peligro DE Incendio O EXPLOSIÓN. Los vapores de losAdvertencias DE Seguridad General Instrucciones DE Conexión a TierraEstos peligros, tome las precauciones siguientes Advertencia Peligro DE Descarga ELÉCTRICA. LaVolts Descripción DE LAS Funciones Instalación Selección DE LA Boquilla DE Pulverización AdecuadaAjuste DE LA Boquilla DE Pulverización Tipo Abanico Preparación DE Materiales Líquidos Figuras E Y E1 Proporciones Comunes DE Dilución EN Latas DE PinturaConsejos DE Prepración Llenado DEL Depósito Figura FFuncionamiento H Ajustes DE Control DE Flujo GDesarrollo DE LA Técnica DE Pulverizaciónadecuada Perilla DE Control DE Flujo Figura GLimpieza Asentada Figura J2Para Iniciar LA Limpieza De limpieza apropiada Consulte las Figuras C y C1Separando la cubierta delantera del pulver Izador Figuras K5 y K6Seque bien todas las piezas ReensamblajeInformación DE Mantenimiento AccesoriosProblema Causa posible Solución posible Detección DE ProblemasSolamente para Propósitos de México 01 800 847 2309/01 800 847Solamente Para Propositos DE Mexico Esta Garantia no Aplica Cuando Años DE GarantiaCat No. BDPS200 Form No September