Ryobi P206 General Maintenance, Batteries, Battery Pack Removal and Preparation for Recycling

Page 14

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING:

Always wear safety goggles or safety glasses with side shields during power product operation or when blowing dust. If operation is dusty, also wear a dust mask.

WARNING:

To avoid serious personal injury, always remove the battery pack from the product when cleaning or performing any maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an Authorized Service Center.

BATTERIES

This product will accept Ryobi One+ 18 V lithium-ion battery packs and Ryobi One+ 18 V nickel-cadmium battery packs.

. Length of service from each charging will depend on the type of work you are doing.

The batteries for this product have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.

To obtain the longest possible battery life, we suggest the following:

For lithium-ion batteries:

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F and away from moisture.

Store battery packs in a 30%-50% charged condition.

Every six months of storage, charge the pack as normal.

For nickel-cadmium batteries:

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F.

Store battery packs in a “discharged” condition.

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

To preserve natural resources, please recycle or dispose of batteries properly.

This product uses nickel-­cadmium and lithium-ion batteries. Local, state or federal laws may prohibit disposal of batteries in ordinary trash.

Consult your local waste authority for information regarding­ available recycling and/or disposal options.

WARNING:

Upon removal, cover the battery pack’s terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its compo- nents. Lithium-ion and nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

14

Image 14
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionPersonal Safety General Safety RulesElectrical Safety Work AreaSpecific Safety Rules ServiceSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Product SpecificationsAssembly Battery Pack Latches To Install Battery PackTo Remove Battery Pack OperationTrigger Unlock Release Chuck Collar Switch TriggerForward Switch Lock Tighten Chuck BodyScrewdriver BIT Adjustable Torque ClutchAdjusting Torque See Installing BitsRemoving Bits Drilling TOP View LevelBattery Pack Removal and Preparation for Recycling MaintenanceGeneral Maintenance BatteriesSee Figures 13 Chuck RemovalTo Retighten a Loose Chuck HEX KEY Mallet Keyless ChuckParts and Service Manuel D’UTILISATION Conserver CE Manuel Pour Future RéférenceGarantie Table DES MatièresRègles DE Sécurité Générales Règles DE Sécurité Particulières DépannageSymboles Symbole NOM Désignation / ExplicationSymbole Signal Signification AvertissementCaractéristiques SpécificationsAssemblage Retrait DU Bloc DE BATTERIES  Installation DU Bloc DE BATTERIES Utilisation Bloc DE Batteries LoquetsUnlock Libération Collier DU Mandrin GâchetteGâchette Lock Blocage Corps DU MandrinEmbrayage DE Couple Réglable Réglage DU CoupleVoir les figures 9 et Installation DES EmboutsRetrait DES Embouts VUE DE Dessus Niveau PerçageVoir les figures 11 et Retrait ET Préparation DU Batteries Pour LE Recyclage EntretienEntretien Général Voir les figures 13 à Retrait DU MandrinSerrage D’UN Mandrin Desserré Mors DU Mandrin CLÉ Hexagonale Maillet Sans CLÉPièces ET Service Manual DEL Operador Garantía Índice DE ContenidoIntroducción Seguridad Eléctrica Reglas DE Seguridad Generales¡ADVERTENCIA Seguridad PersonalReglas DE Seguridad Específicas ServicioSímbolos Símbolo Nombre DENOMINACIÓN/EXPLICACIÓNAdvertencia Símbolo Señal SignificadoEngranaje DE DOS Velocidades ALTA-BAJA CaracterísticasEspecificaciones DEL Producto Armado Para Instalar EL Paquete DE Pilas FuncionamientoAplicaciones PrecauciónMarcha Adelante / Atrás / Seguro EN EL Centro Gatillo DEL InterruptorGatillo DEL Interruptor DE VELOCI- DAD Variable Lock Apretar Cuerpo DEL Porta BrocasAjuste DE LA Fuerza DE Torsión Embrague DE Fuerza DE Torsión AjustableLugar Para Guardar Puntas Vea las figuras 9 y Instalación DE LAS Puntas DE DestornilladorRemoción DE LAS Brocas Vista Superior Nivel Vista Desde EL Extremo TaladradoVea las figuras 11 y Baterías MantenimientoMantenimiento General Vea las figuras 13 a Desmontaje DEL PortabrocasPara Apretar EL Portabrocas Cuan Do SE Afloje Mordazas DEL Portabrocas Llave Hexagonal Mazo GomaPiezas DE Repuesto Y Servicio ONE World TECHNOLOGIES, INC
Related manuals
Manual 18 pages 40.31 Kb