Ryobi P206 manual Switch Trigger, Forward Switch, Trigger Unlock Release Chuck Collar

Page 10

OPERATION

WARNING:

Battery tools are always in operating condition. There- fore, switch should always be locked when not in use or carrying at your side.

SWITCH TRIGGER

See Figure 3.

To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger.

VARIABLE SPEED

The switch trigger delivers higher speed and torque with increased trigger pressure and lower speed with decreased trigger pressure.

NOTE:  You might hear a whistling or ringing noise from the switch during use. Do not be concerned; this is a normal part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 3.

The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for drilling. The drilling direction is reversed when the selector is to the right of the switch trigger.

DIRECTION OF ROTATION SELECTOR

 

(FORWARD/REVERSE/CENTER LOCK)

REVERSE

 

24

 

0

 

2

 

5

 

FORWARD SWITCH

TRIGGER

Fig. 3

UNLOCK

(RELEASE)

CHUCK COLLAR

Setting the switch trigger in the OFF (center lock) position helps reduce the possibility of accidental starting when not in use.

CAUTION:

To prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of rotation.

To stop the drill, release the switch trigger and allow the chuck to come to a complete stop.

LOCK

(TIGHTEN)

CHUCK

BODY

24

2

0

 

5

NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right.

Avoid running the drill at low speeds for extended periods of time. Running at low speeds under constant usage may cause the drill to become overheated. If this occurs, cool the drill by running it without a load and at full speed.

KEYLESS CHUCK

See Figure 4.

The drill has a keyless chuck to tighten or release drill bits in the chuck jaws. Grasp and hold the collar of the chuck with one hand. Rotate the chuck body with your other hand. The arrows on the chuck indicate which direction to rotate the chuck body in order to LOCK (tighten) or UNLOCK (release) the drill bit.

Fig. 4

WARNING:

Do not hold the chuck body with one hand and use the power of the drill to tighten the chuck jaws on the drill bit. The chuck body could slip in your hand, or your hand could slip and come in contact with the rotating drill bit. This could cause an accident resulting in serious personal injury.

10

Image 10
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionPersonal Safety General Safety RulesElectrical Safety Work AreaSpecific Safety Rules ServiceSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Product SpecificationsAssembly Battery Pack Latches To Install Battery PackTo Remove Battery Pack OperationTrigger Unlock Release Chuck Collar Switch TriggerForward Switch Lock Tighten Chuck BodyAdjusting Torque Adjustable Torque ClutchScrewdriver BIT Removing Bits Installing BitsSee Drilling TOP View LevelBattery Pack Removal and Preparation for Recycling MaintenanceGeneral Maintenance BatteriesSee Figures 13 Chuck RemovalTo Retighten a Loose Chuck HEX KEY Mallet Keyless ChuckParts and Service Manuel D’UTILISATION Conserver CE Manuel Pour Future RéférenceGarantie Table DES MatièresRègles DE Sécurité Générales Règles DE Sécurité Particulières DépannageSymboles Symbole NOM Désignation / ExplicationSymbole Signal Signification AvertissementCaractéristiques SpécificationsAssemblage Retrait DU Bloc DE BATTERIES  Installation DU Bloc DE BATTERIES Utilisation Bloc DE Batteries LoquetsUnlock Libération Collier DU Mandrin GâchetteGâchette Lock Blocage Corps DU MandrinEmbrayage DE Couple Réglable Réglage DU CoupleRetrait DES Embouts Installation DES EmboutsVoir les figures 9 et Voir les figures 11 et PerçageVUE DE Dessus Niveau Entretien Général EntretienRetrait ET Préparation DU Batteries Pour LE Recyclage Voir les figures 13 à Retrait DU MandrinSerrage D’UN Mandrin Desserré Mors DU Mandrin CLÉ Hexagonale Maillet Sans CLÉPièces ET Service Manual DEL Operador Introducción Índice DE ContenidoGarantía Seguridad Eléctrica Reglas DE Seguridad Generales¡ADVERTENCIA Seguridad PersonalReglas DE Seguridad Específicas ServicioSímbolos Símbolo Nombre DENOMINACIÓN/EXPLICACIÓNAdvertencia Símbolo Señal SignificadoEspecificaciones DEL Producto CaracterísticasEngranaje DE DOS Velocidades ALTA-BAJA Armado Para Instalar EL Paquete DE Pilas FuncionamientoAplicaciones PrecauciónMarcha Adelante / Atrás / Seguro EN EL Centro Gatillo DEL InterruptorGatillo DEL Interruptor DE VELOCI- DAD Variable Lock Apretar Cuerpo DEL Porta BrocasLugar Para Guardar Puntas Embrague DE Fuerza DE Torsión AjustableAjuste DE LA Fuerza DE Torsión Remoción DE LAS Brocas Instalación DE LAS Puntas DE DestornilladorVea las figuras 9 y Vea las figuras 11 y TaladradoVista Superior Nivel Vista Desde EL Extremo Mantenimiento General MantenimientoBaterías Vea las figuras 13 a Desmontaje DEL PortabrocasPara Apretar EL Portabrocas Cuan Do SE Afloje Mordazas DEL Portabrocas Llave Hexagonal Mazo GomaPiezas DE Repuesto Y Servicio ONE World TECHNOLOGIES, INC
Related manuals
Manual 18 pages 40.31 Kb