Epson D28144R Spindle Lock, Slider Switch D28131, D28140, LOCK-ON Button D28114, D28144

Page 11

To turn the tool on, push the lock-off lever (B) toward the back of the tool, then depress the paddle switch (A). The tool will run while the switch is depressed. Turn the tool off by releasing the paddle switch.

A

B

CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turn-

ing the tool off.

C

SPINDLE LOCK

The spindle lock (C) is provided to prevent

English

WARNING: Do not disable the lock-off lever. If the lock-off lever is disabled, the tool may start unexpectedly when it is laid down.

SLIDER SWITCH (D28131, D28140)

CAUTION: Before connecting the tool to a power supply, be sure the switch is in the off position by pressing the rear part of the switch and releasing. Ensure the switch is in the off position as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure.

To start the tool, slide the ON/OFF switch

 

(L) toward the front of the tool. To stop

 

the tool, release the ON/OFF switch.

 

For continuous operation, slide the

 

switch toward the front of the tool and

L

press the forward part of the switch

 

inward. To stop the tool while operating in continuous mode, press the rear part of the switch and release.

LOCK-ON BUTTON (D28114, D28144)

 

 

 

The lock-on button (J) offers increased

 

 

 

comfort in extended use applications.

 

 

 

To lock the tool on, push the lock-off

 

 

 

lever (B) toward the back of the tool

 

 

 

then depress the paddle switch (A).

 

 

 

With the tool running, depress the

A

B

J

lock-on button (J). The tool will contin-

 

 

 

 

ue to run after the paddle switch is released. To unlock the tool, depress and release the paddle switch. This will cause the tool to stop.

the spindle from rotating when installing or removing wheels. Operate the spindle lock only when the tool is turned off, unplugged from the power supply, and has come to

a complete stop. Do not engage the spindle lock while the tool is operating because damage to the tool will result. To engage the lock, depress the spindle lock button and rotate the spindle until you are unable to rotate the spindle further.

Mounting and Using Depressed Center Grinding Wheels and Sanding Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS

WARNING: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, depress and release the paddle switch to ensure that the tool is off.

Hubbed wheels install directly on the 5/8"-11 threaded spindle. Thread of accessory must match thread of spindle.

1.Backing flange is retained to the grinder by an O-ring on the spindle. Remove backing flange by pulling and twisting flange away form the machine.

2.Thread the wheel on the spindle by hand.

3.Depress the spindle lock button and use a wrench to tighten the hub of the wheel.

4.Reverse the above procedure to remove the wheel.

CAUTION: Failure to properly seat the wheel before turning the tool on may result in damage to the tool or the wheel.

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Guide D’UTILISATION Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety DewaltTool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety ServiceAlways Wear EYE Protection When Using this Tool Clutch D28140, D28144, D28144N FeaturesSwitch Protection POWER-OFF Overload ProtectionComplete Electronic Control Components FigAttaching Side Handle Assembly and Adjustments2 and 5 Grinding Wheels Rotating the Gear CaseSanding Discs Wire WheelsMounting and Removing Guard 2and 5 Sanding Flap Discs AccessoriesMounting Guard Operation SwitchesSoft Start Feature Paddle Switch D28114, D28114N, D28144, D28144NMounting and Removing Hubbed Wheels Slider Switch D28131, D28140Spindle Lock LOCK-ON Button D28114, D28144Edge Grinding with Grinding Wheels Mounting NON-HUBBED WheelsSurface Grinding with Grinding Wheels Mounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Using Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Mounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Lubrication MaintenanceCleaning Accessories Three Year Limited WarrantyDAY Money Back Guarantee Year Free ServiceMesures DE Sécurité Électricité Règles de sécurité GénéralitésAire DE Travail Utilisation ET Entretien DE L’OUTIL Calibre minimal des cordons de rallonge TensionSécurité Personnelle Entretien Causes de l’effet de rebond et prévention par l’opérateur Dispositif E-CLUTCH Composant E-SWITCH Protection Protection E-SWITCHCaractéristiques Embrayage Modèles D28140, D28144 ET D28144NFonction Complete Electronic Control Composants figDisques de Ponçage Brosses métalliques à touret Meules de 114,3 mm et de 127 mm 4-1/2 et 5 poAssemblage DE LA Poignée Latérale AccessoiresAssemblage ET Réglages Montage ET Démontage DU Capot Protecteur Assemblage du capot protecteurFonctionnement Capots protecteurs et bridesFonction DE Démarrage Souple InterrupteursContacteur À Palette Modèles D28114, D28114N, D28144 ET D28144NAssemblage ET Retrait DES Meules À Moyeu Intégré Bouton DE VerrouillageModèles D28114 ET D28144 Dispositif DE Verrouillage DE LA BrocheMeule DE 3,31 MM Meulage DE Surface Avec DES Meules AbrasivesAssemblage DES Tampons Pour LE Ponçage Meulage DE Chant Avec DES Meules AbrasivesFinition DE Surface Avec DES Disques DE Ponçage Lamelles Utilisation DES Tampons Pour LE Ponçage Assemblage et utilisation des brosses métalliquesUtilisation DE Brosses Coniques ET DE BROSSES-BOISSEAU Assemblage et utilisation de disques de Type 1 coupeAssemblage DE Brosses Coniques ET DE BROSSES-BOISSEAU Utilisation DE Disques DE Coupe Assemblage DU Capot Protecteur Fermé TypeAssemblage DE Disques DE Coupe Réparations EntretienNettoyage LubrificationGarantie DE Remboursement DE 90 Jours Contrat D’ENTRETIEN Gratuit D’UN ANSeguridad Eléctrica Instrucciones de seguridad generalesÁrea DE Trabajo Seguridad Personal Calibre mínimo para cordones de extensiónVolts Longitud total del cordón en metros AmperajeServicio Causas del retroceso y su prevención por parte del operador Embrague D28140, D28144, D28144N Protección Contra Sobrecarga POWER-OFFCaracterísticas DES Componentes FigProtector de montaje Ensamblado Y AjustesRotación de la caja de engranajes AccesoriosCon el cerrojo del protector abierto, gire Discos de lijar Discos de corte de 114,3 mm 2 y 127 mmDiscos de alambre Interruptores Discos de lijar de 114,3 mm 4-1/2 y 127 mmFuncionamiento Protectores y bridasBotón DE Bloqueo D28114, D28144 Función DE Arranque SuaveInterruptor DE Paleta D28114, D28114N, D28144, D28144N Interruptor Deslizante D28131, D28140Montaje DE Discos SIN Cubo Montaje Y Extracción DE Discos CON CuboAcabado DE Superficies CON Discos DE Lijar Esmerilado DE Superficie CON Discos DE EsmerilarEsmerilado DE Bordes CON Discos DE Esmerilar USO DE Almohadillas DE Respaldo Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarMontaje y uso de cepillos de alambre y discos de alambre Montaje DE LOS Discos DE Corte Montaje y uso de discos de corte TipoMontaje DEL Protector Cerrado Tipo Reparaciones MantenimientoLimpieza LubricaciónExcepciones Póliza de GarantíaGarantía limitada por tres años Garantía DE Reembolso DE SU Dinero POR 90 Días AÑO DE Servicio Gratuito
Top Page Image Contents