Epson D28144R Mounting and Using Cutting Type 1 Wheels, Mounting Closed Type 1 Guard

Page 15

6. Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before setting it down.

CAUTION: Use extra care when working over an edge, as a sudden sharp movement of grinder may be experienced.

Mounting and Using Cutting (Type 1) Wheels

Cutting wheels include diamond wheels and abrasive discs. Abrasive cutting wheels for metal and concrete use are available. Diamond blades for concrete cutting can also be used.

NOTE: All grinders that use Type 1 wheels use the quick-change backing flange (G1).

WARNING: A closed, 2-sided cutting wheel guard is not included with this tool (D28140, D28144, D28144N ONLY) and is required when using cutting wheels. Failure to use proper flange and guard can result in injury resulting from wheel breakage and wheel contact. See page 7 for more information.

MOUNTING CLOSED (TYPE 1) GUARD

WARNING: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

3. Rotate guard (I) into desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection.

4. Close the guard latch to secure the

I

guard on the gear case cover. You

 

should be unable to rotate the guard by

 

hand when the latch is in closed posi-

 

tion. If rotation is possible, tighten the P

 

adjusting screw (P) with clamp lever in

 

the closed position. Do not operate

 

grinder with a loose guard or clamp

 

lever in open position.

 

5.To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned and pull up on the guard.

NOTE: If, after a period of time, the guard becomes loose, tighten the adjusting screw (P) with the clamp lever in the closed position.

CAUTION: Do not tighten adjusting screw with clamp lever in open position. Undetectable damage to guard or mounting hub may result.

MOUNTING CUTTING WHEELS

WARNING: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces-

English

1.Open the guard latch (M). Align the lugs (N) on the guard with the slots (O) on the gear case.

2.Push the guard down until the guard lug engages and rotates freely in the groove on the gear case hub.

O

N

M

sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

CAUTION: Matching diameter backing flange and threaded clamp nut (included with tool) must be used for cutting wheels.

1.Place the quick-change backing flange on spindle with the raised section (pilot) facing up. The raised section (pilot) on the backing flange will be against the wheel when the wheel is installed.

14

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Guide D’UTILISATION Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety DewaltTool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety ServiceAlways Wear EYE Protection When Using this Tool Clutch D28140, D28144, D28144N FeaturesSwitch Protection POWER-OFF Overload ProtectionComplete Electronic Control Components FigAttaching Side Handle Assembly and Adjustments2 and 5 Grinding Wheels Rotating the Gear CaseSanding Discs Wire Wheels2and 5 Sanding Flap Discs Accessories Mounting GuardMounting and Removing Guard Operation SwitchesSoft Start Feature Paddle Switch D28114, D28114N, D28144, D28144NMounting and Removing Hubbed Wheels Slider Switch D28131, D28140Spindle Lock LOCK-ON Button D28114, D28144Mounting NON-HUBBED Wheels Surface Grinding with Grinding WheelsEdge Grinding with Grinding Wheels Using Sanding Backing Pads Surface Finishing with Sanding Flap DiscsMounting Sanding Backing Pads Mounting and Using Wire Brushes and Wire Wheels Mounting Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 Wheels Mounting Closed Type 1 GuardMounting Cutting Wheels Lubrication MaintenanceCleaning Accessories Three Year Limited WarrantyDAY Money Back Guarantee Year Free ServiceRègles de sécurité Généralités Aire DE TravailMesures DE Sécurité Électricité Calibre minimal des cordons de rallonge Tension Sécurité PersonnelleUtilisation ET Entretien DE L’OUTIL Entretien Causes de l’effet de rebond et prévention par l’opérateur Dispositif E-CLUTCH Composant E-SWITCH Protection Protection E-SWITCHCaractéristiques Embrayage Modèles D28140, D28144 ET D28144NFonction Complete Electronic Control Composants figDisques de Ponçage Brosses métalliques à touret Meules de 114,3 mm et de 127 mm 4-1/2 et 5 poAccessoires Assemblage ET RéglagesAssemblage DE LA Poignée Latérale Montage ET Démontage DU Capot Protecteur Assemblage du capot protecteurFonctionnement Capots protecteurs et bridesFonction DE Démarrage Souple InterrupteursContacteur À Palette Modèles D28114, D28114N, D28144 ET D28144NAssemblage ET Retrait DES Meules À Moyeu Intégré Bouton DE VerrouillageModèles D28114 ET D28144 Dispositif DE Verrouillage DE LA BrocheMeule DE 3,31 MM Meulage DE Surface Avec DES Meules AbrasivesMeulage DE Chant Avec DES Meules Abrasives Finition DE Surface Avec DES Disques DE Ponçage LamellesAssemblage DES Tampons Pour LE Ponçage Utilisation DES Tampons Pour LE Ponçage Assemblage et utilisation des brosses métalliquesAssemblage et utilisation de disques de Type 1 coupe Assemblage DE Brosses Coniques ET DE BROSSES-BOISSEAUUtilisation DE Brosses Coniques ET DE BROSSES-BOISSEAU Assemblage DU Capot Protecteur Fermé Type Assemblage DE Disques DE CoupeUtilisation DE Disques DE Coupe Réparations EntretienNettoyage LubrificationGarantie DE Remboursement DE 90 Jours Contrat D’ENTRETIEN Gratuit D’UN ANInstrucciones de seguridad generales Área DE TrabajoSeguridad Eléctrica Seguridad Personal Calibre mínimo para cordones de extensiónVolts Longitud total del cordón en metros AmperajeServicio Causas del retroceso y su prevención por parte del operador Protección Contra Sobrecarga POWER-OFF CaracterísticasEmbrague D28140, D28144, D28144N DES Componentes FigProtector de montaje Ensamblado Y AjustesRotación de la caja de engranajes AccesoriosCon el cerrojo del protector abierto, gire Discos de corte de 114,3 mm 2 y 127 mm Discos de alambreDiscos de lijar Interruptores Discos de lijar de 114,3 mm 4-1/2 y 127 mmFuncionamiento Protectores y bridasBotón DE Bloqueo D28114, D28144 Función DE Arranque SuaveInterruptor DE Paleta D28114, D28114N, D28144, D28144N Interruptor Deslizante D28131, D28140Montaje DE Discos SIN Cubo Montaje Y Extracción DE Discos CON CuboEsmerilado DE Superficie CON Discos DE Esmerilar Esmerilado DE Bordes CON Discos DE EsmerilarAcabado DE Superficies CON Discos DE Lijar USO DE Almohadillas DE Respaldo Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarMontaje y uso de cepillos de alambre y discos de alambre Montaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte Reparaciones MantenimientoLimpieza LubricaciónPóliza de Garantía Garantía limitada por tres añosExcepciones Garantía DE Reembolso DE SU Dinero POR 90 Días AÑO DE Servicio Gratuito
Top Page Image Contents