Epson D28144R 2and 5 Sanding Flap Discs Accessories, Mounting Guard, Mounting and Removing Guard

Page 9

4-1/2"and 5" Sanding Flap Discs

Accessories

Type 27 guard

hubbed sanding

flap disc

Type 27 guard

Quick-Change

backing flange

non-hubbed sanding

flap disc

threaded clamp nut

It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. See pages 6–8 for infor- mation on choosing the correct accessories.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other acces- sories running over rated accessory speed may burst and cause injury. Threaded accessories must have a 5/8"-11 hub. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 6–8 of this man- ual. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

Mounting Guard

MOUNTING AND REMOVING GUARD

WARNING: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, depress and release the paddle switch to ensure that the tool is off.

CAUTION: Guards must be used with all grinding wheels, sand- ing flap discs, wire brushes, and wire wheels. The tool may be used without a guard only when sanding with conventional sanding discs. Some DeWALT models are provided with a guard intended for use

English

NOTE: If the gear case and motor housing become separated by more than 1/4", the tool must be serviced and re-assembled by a DEWALT service center. Failure to have the tool serviced may cause brush, motor and bearing failure.

4.Re-install screws to attach the gear case to the motor hous- ing. Tighten screws to 18 in./lbs. torque. Overtightening could cause screws to strip.

5.Re-install guard and correct flanges for the appropriate acces- sories.

with depressed center wheels (Type 27) and hubbed grinding wheels (Type 27). The same guard is designed for use with sanding flap discs (Type 27 and 29) and wire brushes. Grinding and cutting with wheels other than Type 27 and 29 require different accessory guards not included with tool. Mounting instructions for these accessory guards are included in the accessory package.

1.Open the guard latch (M). Align the lugs (N) on the guard with the slots (O) on the gear case.

8

Image 9

Contents Guide D’UTILISATION Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsDewalt Work AreaPersonal Safety Additional Specific Safety Instructions for GrindersService Tool USE and CareAlways Wear EYE Protection When Using this Tool Switch Protection FeaturesPOWER-OFF Overload Protection Clutch D28140, D28144, D28144NComplete Electronic Control Components Fig2 and 5 Grinding Wheels Assembly and AdjustmentsRotating the Gear Case Attaching Side HandleSanding Discs Wire Wheels2and 5 Sanding Flap Discs Accessories Mounting GuardMounting and Removing Guard Soft Start Feature SwitchesPaddle Switch D28114, D28114N, D28144, D28144N OperationSpindle Lock Slider Switch D28131, D28140LOCK-ON Button D28114, D28144 Mounting and Removing Hubbed WheelsMounting NON-HUBBED Wheels Surface Grinding with Grinding WheelsEdge Grinding with Grinding Wheels Using Sanding Backing Pads Surface Finishing with Sanding Flap DiscsMounting Sanding Backing Pads Mounting and Using Wire Brushes and Wire Wheels Mounting Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 Wheels Mounting Closed Type 1 GuardMounting Cutting Wheels Cleaning MaintenanceAccessories Three Year Limited Warranty LubricationDAY Money Back Guarantee Year Free ServiceRègles de sécurité Généralités Aire DE TravailMesures DE Sécurité Électricité Calibre minimal des cordons de rallonge Tension Sécurité PersonnelleUtilisation ET Entretien DE L’OUTIL Entretien Causes de l’effet de rebond et prévention par l’opérateur Caractéristiques Composant E-SWITCH Protection Protection E-SWITCHEmbrayage Modèles D28140, D28144 ET D28144N Dispositif E-CLUTCHFonction Complete Electronic Control Composants figDisques de Ponçage Brosses métalliques à touret Meules de 114,3 mm et de 127 mm 4-1/2 et 5 poAccessoires Assemblage ET RéglagesAssemblage DE LA Poignée Latérale Fonctionnement Assemblage du capot protecteurCapots protecteurs et brides Montage ET Démontage DU Capot ProtecteurContacteur À Palette InterrupteursModèles D28114, D28114N, D28144 ET D28144N Fonction DE Démarrage SoupleModèles D28114 ET D28144 Bouton DE VerrouillageDispositif DE Verrouillage DE LA Broche Assemblage ET Retrait DES Meules À Moyeu IntégréMeule DE 3,31 MM Meulage DE Surface Avec DES Meules AbrasivesMeulage DE Chant Avec DES Meules Abrasives Finition DE Surface Avec DES Disques DE Ponçage LamellesAssemblage DES Tampons Pour LE Ponçage Utilisation DES Tampons Pour LE Ponçage Assemblage et utilisation des brosses métalliquesAssemblage et utilisation de disques de Type 1 coupe Assemblage DE Brosses Coniques ET DE BROSSES-BOISSEAUUtilisation DE Brosses Coniques ET DE BROSSES-BOISSEAU Assemblage DU Capot Protecteur Fermé Type Assemblage DE Disques DE CoupeUtilisation DE Disques DE Coupe Nettoyage EntretienLubrification RéparationsGarantie DE Remboursement DE 90 Jours Contrat D’ENTRETIEN Gratuit D’UN ANInstrucciones de seguridad generales Área DE TrabajoSeguridad Eléctrica Volts Longitud total del cordón en metros Calibre mínimo para cordones de extensiónAmperaje Seguridad PersonalServicio Causas del retroceso y su prevención por parte del operador Protección Contra Sobrecarga POWER-OFF CaracterísticasEmbrague D28140, D28144, D28144N DES Componentes FigRotación de la caja de engranajes Ensamblado Y AjustesAccesorios Protector de montajeCon el cerrojo del protector abierto, gire Discos de corte de 114,3 mm 2 y 127 mm Discos de alambreDiscos de lijar Funcionamiento Discos de lijar de 114,3 mm 4-1/2 y 127 mmProtectores y bridas InterruptoresInterruptor DE Paleta D28114, D28114N, D28144, D28144N Función DE Arranque SuaveInterruptor Deslizante D28131, D28140 Botón DE Bloqueo D28114, D28144Montaje DE Discos SIN Cubo Montaje Y Extracción DE Discos CON CuboEsmerilado DE Superficie CON Discos DE Esmerilar Esmerilado DE Bordes CON Discos DE EsmerilarAcabado DE Superficies CON Discos DE Lijar USO DE Almohadillas DE Respaldo Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarMontaje y uso de cepillos de alambre y discos de alambre Montaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte Limpieza MantenimientoLubricación ReparacionesPóliza de Garantía Garantía limitada por tres añosExcepciones Garantía DE Reembolso DE SU Dinero POR 90 Días AÑO DE Servicio Gratuito