Black & Decker D28494 Assembly and Adjustments Attaching the Side Handle, Rotating the Gear Case

Page 12

399080-02 rev 11/15/02 10:13 AM Page 8

English

CAUTION: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other acces- sories running over rated speed can fly apart and cause injury.

ATTACHMENTS

Attachments designed specifically for this grinder can be purchased through DEWALT dealers and DEWALT Factory Service centers.

D284939	9" Type 27 guard
D284948	9" Type 28 guard
D284937	7" Type 27 guard
D284936	6" Type 11 Flaring cup guard with flange
D284934	4" Type 11 Flaring cup guard with flange
D284933	Type 11 flaring cup wheel backing flange
D284932	Type 1 Flange set
D284931	7" Type 1 Guard
054339-00	Grinding backing flange
22191-00	Clamp nut
61820-01	Wheel Wrench
445928-01	Soft mount spindle protector
397711-00	Rubber gear case bumper

ASSEMBLY AND ADJUSTMENTS Attaching the Side Handle

To install the side handle, thread the handle into one of the five positions listed below and tighten securely by turning clockwise.

•Two front positions: Forward handle positions are designed for optimized balance in surface finishing applications.

• Two rear positions: Rear handle positions are designed for optimized balance in edge grinding applications.

•One top position: Top handle position is

designed for edge grinding applications.

NOTE: D28497 includes only three handle positions.

Rotating the Rear Handle

Turn off and unplug tool before making any adjustments or removing or installing accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

1. Unlock the rear handle by pulling out the Handle Re- lease Lever (G) as shown.

2. Rotate handle into available 0°, 30°, 60°, or 90° position left OR right of center.

3. Push in the handle release	G
lever.

4.Before turning the tool on, ensure that the handle is locked into a position and the handle release lever has returned to the orig- inal position flush with the tool housing.

Rotating the Gear Case

Turn off and unplug tool before making any adjustments or removing or installing accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

1.Remove the four corner screws attaching the gear case to motor housing.

8

Image 12

Contents Rev 11/15/02 1013 AM Form No -02 D28474, D28493, D28494, D28499, D28497 Copyright Rev 11/15/02 1013 AM English General Safety Instructions Electrical SafetyWork Area Personal Safety ServiceTool USE and Care Specific Safety Rules for Grinders AccessoryMinimum 5000 RPM 5500 RPM 6000 RPM 6600 RPM 8000 RPM 8500 RPMFeatures SwitchFamiliarization ComponentsAccessories and Attachments Sanding Flap DiscsGrinding Wheels Sanding Discs DW4947 Sanding disc Clamp nut Included with D4947Wire Wheels Flaring Cup Stones Cutting Wheels Wire wheel608463-00 Assembly and Adjustments Attaching the Side Handle Rotating the Rear HandleRotating the Gear Case AttachmentsPower Source SwitchOperation Important Information about Guards Mounting and Removing Hubbed WheelsMounting NON-HUBBED Wheels Surface Grinding with Grinding Wheels Edge Grinding with Grinding WheelsSurface Finishing with Sanding Flap Discs Mounting and Using Sanding Backing Pads Using Sanding Backing PadsMounting Sanding Backing Pads Mounting and Using Wire Brushes and Wire Wheels Mounting and Using Flaring Cup Type 11 WheelMounting Wire Brushes and Wire Wheels Using Wire CUP Brushes and Wire WheelsMounting and Using Cutting Using a Flaring CUP WheelType 1 Wheels Mounting Flaring CUP WheelMaintenance CleaningUsing Cutting Wheels LubricationPurchasing Accessories Full WarrantyDAY no Risk Satisfaction Guarantee RepairsMesures DE Sécurité Généralités Conserver CES Directives Zone DE TravailMesures DE Sécurité Électricité Sécurité Personnelle Utilisation ET Entretien DE L’OUTILRègles de sécurité spécifique concernant les meules EntretienFamiliarisation Composants CaractéristiquesAccessoires AccessoiresDisques de ponçage à feuillets Bague EN NylonMeules Disques de ponçage Disque de ponçage Écrou de blocage D4947608370-00 Assemblage ET Réglage Installation de la poignée latérale Positionnement du carter d’engrenagesPositionnement de la poignée arrière De la poignéeFonctionnement Source d’alimentationInterrupteur à gâchette Français Installation DES Meules Sans Moyeu Meulage DE BordureMeulage DE Finition Installation DES Tampons DE Support Caoutchouc L sur la bague en nylonUtilisation DES Tampons DE Support Installation DES Brosses ET DES Meules Métalliques Es à billes métalliquesInstallation et utilisation des meules boisseaux coniques n Installer le dispositif de protection tel qu’indiquéInstallation DES Meules Boisseaux Coniques Remarque Régler la jupe de protection de manière que seuleInstallation et utilisation des meules abrasives n Installation DU Dispositif DE Protection Fermé NEntretien NettoyageLubrification RéparationRemplacement Gratuit DE Létiquette Garantie complète d’un anGarantie Sans Risque DE 30 Jours EN CAS DE NON-SATISFACTION Instrucciones generales de seguridad Conserve Estas Instrucciones Área DE TrabajoSeguridad Eléctrica Seguridad Personal USO Y Cuidados DE LA HerramientaInstrucciones de seguridad específicas para esmeriladoras ServicioVelocidad sin Classificación Conocimiento DEL Producto Componentes CaracterísticasDiscos para esmerilar Discos de lijar Cepillos de Copa de Piedra Discos de corte Alambre Discos de aleta para lijar AccesoriosMontaje Suave DispositivosEnsamblaje Y Ajustes Instalación del mango lateralComo girar mango trasero Como girar la caja de engranajesOperación Alimentación de corrienteInterruptor Información Importante Sobre LAS Guardas Instalación Y Remoción DE LOS Discos DE CuboInstalación DE Discos CON Centro Deprimido Esmerilado DE CON Discos DE EsmerilarEsmerilado DE Bordes CON Discos DE Esmerilar Acabado DE Superficies CON Discos DE Aleta Para LijarInstalación y utilización de las para lijar Utilización DE Respaldo DE GomaAcabado muy fino Sobre el montaje suaveInstalación y utilización de copas y ruedas de alambre Instalación y utilización de piedras de copaInstalación DE Copas Y Discos DE Alambre Instalación DE LA Guarda DE LAS Piedras DE CopaInstalación y utilización de discos de corte tipo Instalación DE LA Piedra DE CopaUtilización DE UNA Piedra DE Copa Instalación DE Guarda Cerrada Tipo Instalación DE Discos DE CorteUtilización DE Discos DE Corte Mantenimiento Póliza de Garantía Garantía completa de un añoExcepciones Información Técnica D28474