Bosch Power Tools 1618EVS, 1617EVSPK, 16186 manual Adapter optional accessory, Centering Cone

Page 20

BM 2610018532 01-12:BM 2610018532 01-12.qxp 1/23/12 9:21 AM Page 20

INSTALLING TEMPLET GUIDE ADAPTER (Not included, available as accessory)

Place templet guide adapter over the holes in the center of the sub-base, and align the two threaded holes in the bottom of adapter with the countersunk holes in sub-base. Fasten adapter with the screws provided. Note that the adapter is reversible, so the release lever may be positioned as desired. (Fig. 25)

FIG. 25

TEMPLET GUIDE

ADAPTER (optional accessory)

MOUNTING SCREWS

CENTERING THE SUB-BASE OR

TEMPLET GUIDES

Your router features the Bosch “Precision Centering Design”. Its sub-base is precisely centered at the factory. This positions the bit at the center of the sub-base and optional templet guides.

Precision centering allows you to use the edge of the subbase or templet guides to closely follow jigs such as straight guides, templets, and dovetail fixtures without worrying about bit walk-off from the intended cut line for any reason, including the orientation of the router’s handles relative to the jig.

To quickly re-center the sub-base, attach the sub-base using the set of flathead screws (included) and the countersunk screw holes in the sub-base. (Flathead screws have the

tapered heads.) The flathead screws and countersunk holes will pull the sub-base into a position that is very close to centered.

To most precisely re-center the sub-base or templet guides, attach the sub-base using the optional Bosch RA1151 Centering Device. Follow steps 1-8 (Fig. 26 & 27).

1.If a templet guide is to be centered, Install the templet guide adapter and template guide (optional attachments) as described elsewhere in this manual.

2.Position the sub-base so that its pan-head screw holes are over the matching set of threaded holes in the base.

3.Insert the pan-head screws through the sub- base and tighten them until they are snug, but still allow the sub-base to move.

CENTERING CONE

CENTERING SHAFT

(optional accessory)

(optional accessory)

 

 

 

 

 

 

 

FIG. 27

 

 

 

 

 

OTHER BASES

FIG. 26

 

 

 

 

 

PLUNGE BASE

 

 

 

 

 

CENTERING SHAFT

 

 

 

 

(optional accessory)

 

 

 

 

TEMPLET GUIDE

 

 

 

 

 

(optional accessory)

D

 

 

 

 

 

C

B

A

SUB-BASE

B

A

 

 

 

A

 

 

 

B

 

 

 

 

 

 

D

 

C

D

 

CENTERING SHAFT (optional accessory)

A = M4 COUNTERSUNK SCREW HOLES

B = M4 PAN-HEAD SCREW HOLES

C = TEMPLET GUIDE ADAPTER SCREW HOLES

D = HOLES FOR ATTACHING ROUTER TO ROUTER TABLE MOUNTING PLATE (Under sub-base on non-plunge bases)

-20-

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Leer antes de usar BM 2610018532 01-12BM 2610018532 01-12.qxp 1/23/12 921 AMCall Toll Free for See Voir Ver la páginaGeneral Power Tool Safety Warnings Work area safetyElectrical safety Personal safetySafety Rules for Routers ServiceMany accidents are caused by poorly maintained power tools Protruding cutting bit may cause tool to jumpAdditional Safety Warnings Some dust created by powerSafety Rules for Router Table Accidental start-up of the tool can cause injurySymbols Name Designation/ExplanationSymbols 1618EVS Functional Description and SpecificationsRouters Motor Housing Speed Control DialBase Type P Depth ROD Knob Chip DeflectorAssembly Installing a Router BITRemoving the Router BIT Collet Chuck CareBase Installing Motor in BaseBase Clamp Lever Fine Adjustment Dial Indicator Ring Cast Indicator Marks Coarse Adjustment LeverDepth Adjustment With Fixed Base To Adjust DepthCoarse Adjustment To Clamp Motor Fine Depth AdjustmentDepth Adjustment with Plunge Base Plunging Action Deep CutsFine Adjustment Depth ROD and TurretRocker ON/OFF Switch Rocker Power ON-OFF with Trigger Switch and LOCK- OnbuttonDial Setting RPM Application Electronic Variable Speed ControlFeeding the Router Start HereBIT Direction Router Feed Rate of FeedUsing the Hood for Backside Fixed Base Router Dust CollectionRouter Dust Collection for Plunge Base M4 Thumb Screws Dust Extraction HoodEdgeforming Dust Extraction Hood Router SUB-BASE Workpiece Edge Dust Extraction HoodM4 x 16mm ScrewFeed Direction M6 Wing Screw Fine Adjustment Indicator Deluxe Router GuideCUT Templet GuidesAdapter optional accessory Mounting Screws Centering the SUB-BASE or Templet GuidesCentering Cone = M4 Countersunk Screw Holes = M4 PAN-HEAD Screw HolesUSE in Router Table Maximum BIT/CUTTER Size for Templet GuidesUSE with Threaded Templet Guides Attaching Base to Mounting Plate Connect the RouterFeeding the Workpiece On a Router Table TOP View Direction Feed Fence FaceExtension Cords MaintenanceCleaning Accessories Sécurité du lieu de travail Sécurité électriqueRègles de sécurité concernant les toupies Utilisation et entretien des outils ÉlectroportatifsEntretien En saillie peut faire sauter loutilAvertissements supplémentaires concernant la sécurité Le plomb provenant des peintures à base de plombConsignes de sécurité pour table de toupillage Symboles Symbole Nom Désignation/ExplicationTours, coups, vitesse en surface, orbites La vitesse augmente depuis le réglageSymboles suite Description fonctionnelle et spécifications ToupiesModéle 1617EVSP uniquement Tige DE Profondeur Déflecteur DE CopeauxAssemblage Montage DU Moteur SUR UNE Embase Levier DE Serrage DE BaseDE Serrage Encoches DE RéglageConsignes de fonctionnement Cadran DE Réglage DE PrécisionLevier DE Serrage DE LA Base Pour Régler LA ProfondeurRéglage Grossier Réglage FIN DE LA ProfondeurPour Brider LE Moteur Usinages ProfondsTige ET Tourelle DE Profondeur Défonceuse, apportant ainsi une grande précision d’usinageTR/MIN Application Circuit Constant ResponseAvance DE LA Défonceuse Comme Ncer ICIFER Sens DE ’AVANCE Vitesse D’AVANCE Guidage DE LA DéfonceuseAvec Embase Plongeante Capuchon ’EXTRACTION DE PoussièreDE Poussière Embase DE DéfonceuseBM 2610018532 01-12BM 2610018532 01-12.qxp 1/23/12 922 AM Ramassage DE Poussière LorsPoussières Chant DE LA PièceCoupe VIS Moletée Guide DE Défonceuse DE LuxeGabarit DE Guidage FERPréparez le dispositif de centrage Adaptateur DUOption Système à relâchement rapide de Bosch Tableau ci-dessousGabarit Utilisation EN Table DE ToupillageMontage DE L’EMBASE SUR LA Plaque DE Montage Réglage DE LA Profondeur voir page 35 etAvance DE LA Pièce SUR UNE Table DE Toupillage VUE DE DessusNettoyage EntretienCordons de rallonge Accessoires Clé de 24 mm pour écrou de douilleSeguridad personal Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones Normas de seguridad para fresadorasMecánicas Advertencias de seguridad adicionales Instrucciones de seguridad para la mesa de fresadora Un número más alto significa mayor velocidad SímbolosSímbolo Nombre Designación/explicación Símbolos continuación Descripción funcional y especificaciones FresadorasSubbase Flecha DE Rotacion DE LA BrocaBase Tipo P DEL MotorMango Izquierdo Subbase Flecha DE Rotacion DE LA BrocaEnsamblaje Seleccion DE BrocasRemocion DE LA Broca DE Fresadora PORTA- HerramientaPara quitar el motor de la base de descenso vertical Fig Instalación DEL Motor EN LA BaseFlechas Palanca DE Ajuste Basto Palanca DE Fijacion DE LA BaseInstrucciones de funcionamiento Deflector DE VirutasPara Ajustar LA Profundidad Abra la palanca de fijación de la base para soltar el motorAjuste Grueso Ajuste DE Profundidad FinoPara Fijar EL Motor Cortes ProfundosVarilla DE Profundidad Y Torreta Fresadora para lograr una precisión superior de fresadoApagado Interruptor Oscilante DE Encendido ApagadoDispositivo DE Arranque Suave Control Electronico DE Velocidad VariableAvance DE LA Fresadora Velocidad DE AvanceComience Aquí Broca Sentido DE Avance DE LA FresadoraLA Base DE Descenso Vertical Manual M4Cubierta DE Extracción DE Polvo Trasero DE LA Base FijaDE Polvo Tornillo Colocación DE LA Cubierta DE Extracción DE PolvoBorde DE LA Pieza DE Trabajo Guía DE Fresadora DE Lujo CorteAnchura Pieza DE Deseada Trabajo Ajuste Fino Guías DE PlantillaInstalación DEL Adaptador DE Guías DE Plantilla Montaje Centrado DE LA Subbase LAS Guías DE PlantillaCono DE Centrado Guía DE PlantillaTamaño Máximo DE BROCA/CORTADOR Para LAS Guías DE Plantilla USO CON Guías DE Plantilla RoscadasUSO EN UNA Mesa DE Fresadora 10-24Sujeción DE LA Base a LA Placa DE Montaje DE LA Mesa DE FresadoraAvance DE LA Pieza DE Trabajo Sobre UNA Mesa DE Fresadora Vista SuperiorMantenimiento Cordones de extensiónServicio LimpiezaAccesorios = equipo estándar = accesorios opcionalesRemarques Notas 2610018532
Related manuals
Manual 68 pages 11.18 Kb
Top Page Image Contents