DSCover Satellite Products SCW904x manual 600 2-way Audio Control Options Applies to SCW9047 only

Page 31

7.2 Programming Worksheets

[600] 2-way Audio Control Options (Applies to SCW9047 only)

Opt Def. ON

1Tampers Enabled

2Openings & Closings Enabled

3[A] Key Alarm Enabled

4[P] Key Alarm Enabled

5Duress Alarm Enabled (Listen)

6Opening after Alarm Enabled

*7	Bell Active during 2-way Audio Verification.

8Future Use

*This option must be ON for UL Listed Installations

INTERNATIONAL PROGRAMMING

[700] Automatic Clock Adjust

Default = 60			Valid Entries 01-99 Seconds
[701] First International Options
Opt	Def.	ON
1	EU	50 Hz AC

2Time Base - Internal Crystal

3AC/DC Arming Inhibit Enabled

4All System Tampers Require Installer Reset

56-digit User Access Codes

6Busy Tone Detection Enabled

7-8	Future Use

NA

OFF

Disabled

Disabled

Disabled

Disabled

Disabled

Disabled

Bell Silent during 2-way Audio Verification.

OFF

60 Hz AC

Time Base - AC Line

AC/DC Arming Inhibit Disabled

All System Tampers Follow Restoral 4-digit User Access Codes

Busy Tone Detection Disabled

[702] Second International Options

Opt Def. ON

1Pulse Dialing Make/Break Ratio is 33/67

2Force Dialing Enabled

3Future Use

41600Hz Handshake

5ID Tone Enabled

62100 Hz ID Tone

7-8	Future Use

OFF

Pulse Dialing Make/Break Ratio is 40/60 Force Dialing Disabled

Standard Handshake

ID Tone Disabled

1300 Hz ID Tone

[703] Delay Between Dialing Attempts

Default = 003

Valid Entries are 000-255 Seconds (Entry + 5 seconds)

WWW.DIYALARMFORUM.COM27

Image 31

Contents Installation Guide Selecting a Suitable Location For The Alarm Controller Before Installing The EquipmentSafety Precautions required during Installation Table of Contents Page Technical Summary Installation & WiringEnsure connector key is oriented correctly InstallationBurglary Zone Wiring Chart WiringMax wire Length to End-of-line Resistor Self Contained Wireless Alarm System Verify Device Electronic Serial Number ESN Wireless Device EnrollmentEnter Wireless Enrollment Mode Activate Wireless DeviceZone Dependant Devices Detectors Zone Definitions Options 1 Template ProgrammingDigit 3 selects 1 of the 8 following options Installer Lead-in/Lead-out and DLS Lead-in/Lead-out Local Programming with PC-Link New Installations Refer to .1 Installation onExisting Installations Refer to .1 Installation on DLS ProgrammingOperation Program User Codes Alarm Memory DisplayDoor Chime Enable/Disable Trouble Display9User Code No-Entry Arming 7x Command Outputs 1&2Installer Programming Additional Keypad FunctionsAdvanced Programming Index to Programming Work Sheets and Descriptions Programming Work SheetsZone Definitions Programming WorksheetsFunction Key Programming Function Key OptionsKeypad Lockout Options Installer’s Code Master CodeSystem Times 009 I/O ProgrammingTenth System Options Second System OptionsThird System Options Fourth System OptionsZone Attributes Options 10-13 are reserved for Future Use Zone Loop Response OptionsNo Activity Arming Timer PGM Output TimerCross Zone/Police Code Timer No Activity Arming Pre-alert TimerPriority Alarm and Restoral Reporting Codes Alarm Reporting Codes, ZonesAlarm Restoral Reporting Codes, Zones Miscellaneous Alarm Reporting CodesTamper Restoral Reporting Codes, Zones Tamper Reporting Codes, ZonesMiscellaneous Opening Disarming Reporting Codes Communicator Format Options Tamper/Restore Communicator Call DirectionsOpening/Closing Communicator Call Directions Test Transmission Time of Day System Maintenance Communicator Call DirectionsSystem Test Transmissions Communicator Call Directions Communication VariablesThird Communicator Options Second Communicator OptionsDownloading Options Attribute Number of Rings To Answer OnInitiate PC-Link Downloading PGM Output AttributesFirst International Options Automatic Clock AdjustDelay Between Dialing Attempts 600 2-way Audio Control Options Applies to SCW9047 onlyWireless Supervisory Window Wireless programming Wireless Zone ProgrammingRestore Wireless Device Default Programming General Wireless OptionsWireless Module Placement Test Installer Lockout Enable Installer Lockout DisableLabel Programming Zone Local Keypad ProgrammingCommand Output #2 Label Fire Alarm LabelAlarm When Armed Event Message Command Output #1 LabelThird Keypad Options Reset Programmable Labels to Factory DefaultsFirst Keypad Options Second Keypad OptionsKeypad Function Key Programming Programming Descriptions002 Zone Definitions O Programming Zones/PGMs Installer CodeSystem Times Master CodeSecond System Options First System OptionsThird System Options Tenth System Options Fourth System OptionsOFF Keypad Always Active. The keypad does not blank Standard Time Set Clock Back Zone Loop Response Options134 Zone Attributes Daylight Saving Time Move Clock AheadCall Waiting Cancel String PGM Output TimerCross Zone/Police Code Timer No Activity Arm TimerTest Transmission Time Communicator VariablesFirst Communicator Options First Downloading Options OFF Closing Confirmation Disabled. The keypad does not beepSecond Communicator Options Third Communicator OptionsNumber of Rings to Answer On Downloading Access CodeDownloading Computer Phone Number Panel Identification CodeWay Audio Control Options applies to SCW9047 only Automatic Clock AdjustFollowing attributes are available for PGM Output Type Second International Options Delay Between Dialing AttemptsWireless Programming First International OptionsRestore Wireless Device Default Programming Wireless Module Placement TestInstaller Lockout Enable Installer Lockout DisableKeypad Programming Fire Alarm LabelsAlarm when Armed Event Message 069 Command Output LabelOption Description Future Use OFF Power LED is disabled. Option 6 has no effectFirst Keypad Options Second Keypad OptionsProgrammed LCD Message Duration Label ResetThird Keypad Options Programmed LCD MessageTesting & Troubleshooting Trouble 8 Loss of Clock/Date Trouble 4 Failure to CommunicateContact ID Appendix a Reporting Code FormatsSIA Format Automatic Zone Alarm/Restoral Codes Contact ID Zone Alarm/Restoral Event CodesAppendix B Communicator Format Options Residential Dial PagerNorth America Appendix C Regulatory Approvals InformationEurope SIA False Alarm Reduction InstallationsNew Zealand Exit Time Appendix D SIA False Alarm ReductionFormat Reporting Code/Event Appendix E 2-Way Audio Verification SCW9047 onlyBell/Buzzer Silent During 2-Way Audio Key Command DescriptionVOX Support Hang-up Auto-detectionPage FCC Compliance Statement