DSCover Satellite Products SCW904x manual Second Communicator Options, Third Communicator Options

Page 29

			7.2 Programming Worksheets
[381] Second Communicator Options
Opt	Def.	ON	OFF
1		Opening After Alarm Keypad Ringback Enabled	Disabled
2		Future Use
3		SIA Uses Programmed Reporting Codes	SIA Uses Automatic Reporting Codes
4		Closing Confirmation Enabled	Closing confirmation Disabled
*5		Talk/Listen on Phone #1/3 Enabled	Talk/Listen #1/3 Disabled
*6		Talk/Listen on Phone #2 Enabled	Talk/Listen #2 Disabled
7		Contact ID Uses Programmed Reporting Codes	Contact ID Uses Automatic Reporting Codes
8		Future Use
*These Options apply to SCW9047 Only. For SCW9045 default is OFF
[382] Third Communicator Options
Opt	Def.	ON	OFF
1		Contact ID Partial Closing Identifier is “5”	Contact ID Partial Closing Identifier is “4”
2		Alarm Communications Enabled During Walk Test*	Alarm Communications Disabled During Walk Test
3		Communication Cancelled Message Enabled (ON for SIA CP-01)	Communication Cancelled Message Disabled
4		Call Waiting Cancel Enabled**	Call Waiting Cancel Disabled

5Future Use

6	AC Failure Transmission Delay is in Hours	AC Failure Transmission Delay is in Minutes
7	Number of Dialing Attempts is 1 for Residential Dial	Residential Dialing Attempts is 5

8Future Use

*This option must remain OFF for SIA-FAR installations.

** A Call Waiting Cancel on a non-Call Waiting line will prevent successful connection to the central station.

DLS Downloading

[401] Downloading Options

Opt	Def. ON	OFF
1	Answering Machine/Double Call Enabled	Answering Machine/Double Call Disabled
2	User Can Enable DLS Window	User Cannot Enable DLS Window
3	Call Back Enabled	Call Back Disabled
4	User Initiated Call Up Enabled	User Initiated Call Up Disabled
5	Future Use
6	300 Baud Panel Call up	110 Baud Panel Call up

7Future Use

8Future Use

[402] DLS Downloading Telephone Number (32 Digits)

D
[403]-[404] DLS Downloading Access Code / Panel ID Code (Enter 6 Hexadecimal Digits)
[403] Downloading Access Code	[404] Panel ID Code	SCW9045 Default = 904500/904500
__________________________________________	__________________________________________	SCW9047 Default = 904700/904700
__________________________________________	__________________________________________

WWW.DIYALARMFORUM.COM25

Image 29

Contents Installation Guide Safety Precautions required during Installation Before Installing The EquipmentSelecting a Suitable Location For The Alarm Controller Table of Contents Page Technical Summary Installation & WiringEnsure connector key is oriented correctly InstallationMax wire Length to End-of-line Resistor WiringBurglary Zone Wiring Chart Self Contained Wireless Alarm System Enter Wireless Enrollment Mode Wireless Device EnrollmentActivate Wireless Device Verify Device Electronic Serial Number ESNZone Dependant Devices Detectors Zone Definitions Options 1 Template ProgrammingDigit 3 selects 1 of the 8 following options Installer Lead-in/Lead-out and DLS Lead-in/Lead-out Existing Installations Refer to .1 Installation on New Installations Refer to .1 Installation onDLS Programming Local Programming with PC-LinkOperation Door Chime Enable/Disable Alarm Memory DisplayTrouble Display Program User CodesInstaller Programming 7x Command Outputs 1&2Additional Keypad Functions 9User Code No-Entry ArmingAdvanced Programming Index to Programming Work Sheets and Descriptions Programming Work SheetsFunction Key Programming Programming WorksheetsFunction Key Options Zone DefinitionsSystem Times Installer’s Code Master Code009 I/O Programming Keypad Lockout OptionsThird System Options Second System OptionsFourth System Options Tenth System OptionsZone Attributes Options 10-13 are reserved for Future Use Zone Loop Response OptionsCross Zone/Police Code Timer PGM Output TimerNo Activity Arming Pre-alert Timer No Activity Arming TimerAlarm Restoral Reporting Codes, Zones Alarm Reporting Codes, ZonesMiscellaneous Alarm Reporting Codes Priority Alarm and Restoral Reporting CodesMiscellaneous Opening Disarming Reporting Codes Tamper Reporting Codes, ZonesTamper Restoral Reporting Codes, Zones Opening/Closing Communicator Call Directions Tamper/Restore Communicator Call DirectionsCommunicator Format Options System Test Transmissions Communicator Call Directions System Maintenance Communicator Call DirectionsCommunication Variables Test Transmission Time of DayDownloading Options Second Communicator OptionsThird Communicator Options Initiate PC-Link Downloading Number of Rings To Answer OnPGM Output Attributes AttributeDelay Between Dialing Attempts Automatic Clock Adjust600 2-way Audio Control Options Applies to SCW9047 only First International OptionsWireless Supervisory Window Wireless programming Wireless Zone ProgrammingWireless Module Placement Test Installer Lockout Enable General Wireless OptionsInstaller Lockout Disable Restore Wireless Device Default ProgrammingLabel Programming Zone Local Keypad ProgrammingAlarm When Armed Event Message Fire Alarm LabelCommand Output #1 Label Command Output #2 LabelFirst Keypad Options Reset Programmable Labels to Factory DefaultsSecond Keypad Options Third Keypad Options002 Zone Definitions Programming DescriptionsKeypad Function Key Programming System Times Installer CodeMaster Code O Programming Zones/PGMsThird System Options First System OptionsSecond System Options OFF Keypad Always Active. The keypad does not blank Fourth System OptionsTenth System Options 134 Zone Attributes Zone Loop Response OptionsDaylight Saving Time Move Clock Ahead Standard Time Set Clock BackCross Zone/Police Code Timer PGM Output TimerNo Activity Arm Timer Call Waiting Cancel StringFirst Communicator Options Communicator VariablesTest Transmission Time Second Communicator Options OFF Closing Confirmation Disabled. The keypad does not beepThird Communicator Options First Downloading OptionsDownloading Computer Phone Number Downloading Access CodePanel Identification Code Number of Rings to Answer OnFollowing attributes are available for PGM Output Type Automatic Clock AdjustWay Audio Control Options applies to SCW9047 only Wireless Programming Delay Between Dialing AttemptsFirst International Options Second International OptionsInstaller Lockout Enable Wireless Module Placement TestInstaller Lockout Disable Restore Wireless Device Default ProgrammingAlarm when Armed Event Message Fire Alarm Labels069 Command Output Label Keypad ProgrammingFirst Keypad Options OFF Power LED is disabled. Option 6 has no effectSecond Keypad Options Option Description Future UseThird Keypad Options Label ResetProgrammed LCD Message Programmed LCD Message DurationTesting & Troubleshooting Trouble 8 Loss of Clock/Date Trouble 4 Failure to CommunicateContact ID Appendix a Reporting Code FormatsSIA Format Automatic Zone Alarm/Restoral Codes Contact ID Zone Alarm/Restoral Event CodesAppendix B Communicator Format Options Residential Dial PagerNorth America Appendix C Regulatory Approvals InformationNew Zealand SIA False Alarm Reduction InstallationsEurope Exit Time Appendix D SIA False Alarm ReductionFormat Reporting Code/Event Appendix E 2-Way Audio Verification SCW9047 onlyVOX Support Key Command DescriptionHang-up Auto-detection Bell/Buzzer Silent During 2-Way AudioPage FCC Compliance Statement