DSCover Satellite Products SCW904x manual Burglary Zone Wiring Chart

Page 7

1.2 Wiring

1.2 Wiring

1. Zone Wiring

Zones can be wired for Normally Open, Normally Closed Contacts with Single- end-of-line (SEOL) resistors or Double End-of-Line (DEOL) resistors. Observe the following guidelines

For UL/ULC listed installations use SEOL or DEOL only.

Minimum 22 AWG wire, maximum 18 AWG

Do NOT use shielded wire

Wire run resistance shall not exceed 100Ω. Refer to the chart below.

 

Burglary Zone Wiring Chart

Wire

Max wire Length to End-of-line Resistor

Gauge

(feet/meters)

 

 

22

3000 / 914

 

 

20

4900 / 1493

 

 

19

6200 / 1889

 

 

18

7800 / 2377

 

 

Figures are based on maximum wiring resistance of 100Ω

Section [009] Selects Hardwired Zone Definition

Sections [133], [134] Opt [14] selects Normally Closed

Sections [133], [134] Opt [15] selects SEOL resistors

Sections [133], [134] Opt [16] selects DEOL resistors.

Zone Status - Loop Resistance/Loop Status

Fault - 0Ω (shorted wire/loop)

Secure - 5600Ω (contact closed)

Tamper - infinite (broken wire, open)

Violated - 11,200Ω (contact open)

Normally Closed Loops - Do NOT use for UL Installations

Single End-of-Line Resistor Wiring

Double End-of-Line Resistor Wiring

2. PGM/Aux Power Wiring

PGMs switch to ground when activated by control panel.

Connect the plus side of the device to be activated to the AUX+ Terminal. Con- nect the minus terminal to the PGM. Each PGM can provide 50mA output.

NOTE: The control panel can provide a maximum of 100mA of AUX current for PGMs, relays, LED’s etc. Min/Max operating voltages for PGMs, relays and modules is 10.2VDC - 13.75VDC

NOTE: Battery Voltage (6.0-8.4VDC) is boosted internally to supply 12VDC on the AUX+ output by setting Sect[014] Opt[4] to ON. This option must be enabled for PGMs used in UL/ULC Residential Burg installations. This output can NOT be used for UL/ULC Fire installations.

LED output with

I/O

I/O

current limiting

resistor and optional Relay driver output

3. Telephone Line Wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ-31x Connector as indicated. Use 24 AWG wire minimum for wiring.

For connection of multiple devices to the telephone line, wire in the sequence indicated.

Communication format is programmed in section [350]. Telephone Call Directions are programmed in section [351]-[376].

T-1

R-1

TIP

RING

BRN

 

GRA

 

GRN

 

RED

RJ-31X

 

Note: For UL Listed Installations,the Installer must verify the communication format with the supervising station at the time of the installation.

4. Battery

5. AC Wiring

A 1500 mAHr Ni-Mh battery pack is included to meet standby power require- ments

NOTE: UL/ULC Residential Burglary installations require 4 Hr. power standby time plus 4 minutes alarm annunciation.

NOTE: UL/ULC Residential Fire installations require 24 Hr. power standby plus 5 minutes alarm annunciation

NOTE: Battery life is 4-5 years under typical operating conditions. Battery capacity deteriorates with age and number of charge/discharge cycles. Replace battery every 4-5 years.

AC Transformer Requirements:

Primary:120VAC, 50/60Hz., 0.33A

240VAC, 50/60Hz., 0.165A Secondary: 16.5VAC/20VA

The following Transformers shall be used:

UL Listed Installations - PTD1620U, PTD1640U (60Hz.) ULC Listed installations - PTD1620, PTD1640 (60Hz.) EU Installations - PTD1620T-EU (50 Hz.)

WWW.DIYALARMFORUM.COM3

Image 7
Contents Installation Guide Selecting a Suitable Location For The Alarm Controller Before Installing The EquipmentSafety Precautions required during Installation Table of Contents Page Technical Summary Installation & WiringEnsure connector key is oriented correctly InstallationBurglary Zone Wiring Chart WiringMax wire Length to End-of-line Resistor Self Contained Wireless Alarm System Verify Device Electronic Serial Number ESN Wireless Device EnrollmentEnter Wireless Enrollment Mode Activate Wireless DeviceZone Dependant Devices Detectors Zone Definitions Options 1 Template ProgrammingDigit 3 selects 1 of the 8 following options Installer Lead-in/Lead-out and DLS Lead-in/Lead-out Local Programming with PC-Link New Installations Refer to .1 Installation onExisting Installations Refer to .1 Installation on DLS ProgrammingOperation Program User Codes Alarm Memory DisplayDoor Chime Enable/Disable Trouble Display9User Code No-Entry Arming 7x Command Outputs 1&2Installer Programming Additional Keypad FunctionsAdvanced Programming Index to Programming Work Sheets and Descriptions Programming Work SheetsZone Definitions Programming WorksheetsFunction Key Programming Function Key OptionsKeypad Lockout Options Installer’s Code Master CodeSystem Times 009 I/O ProgrammingTenth System Options Second System OptionsThird System Options Fourth System OptionsZone Attributes Options 10-13 are reserved for Future Use Zone Loop Response OptionsNo Activity Arming Timer PGM Output TimerCross Zone/Police Code Timer No Activity Arming Pre-alert TimerPriority Alarm and Restoral Reporting Codes Alarm Reporting Codes, ZonesAlarm Restoral Reporting Codes, Zones Miscellaneous Alarm Reporting CodesTamper Restoral Reporting Codes, Zones Tamper Reporting Codes, ZonesMiscellaneous Opening Disarming Reporting Codes Communicator Format Options Tamper/Restore Communicator Call DirectionsOpening/Closing Communicator Call Directions Test Transmission Time of Day System Maintenance Communicator Call DirectionsSystem Test Transmissions Communicator Call Directions Communication VariablesThird Communicator Options Second Communicator OptionsDownloading Options Attribute Number of Rings To Answer OnInitiate PC-Link Downloading PGM Output AttributesFirst International Options Automatic Clock AdjustDelay Between Dialing Attempts 600 2-way Audio Control Options Applies to SCW9047 onlyWireless Supervisory Window Wireless programming Wireless Zone ProgrammingRestore Wireless Device Default Programming General Wireless OptionsWireless Module Placement Test Installer Lockout Enable Installer Lockout DisableLabel Programming Zone Local Keypad ProgrammingCommand Output #2 Label Fire Alarm LabelAlarm When Armed Event Message Command Output #1 LabelThird Keypad Options Reset Programmable Labels to Factory DefaultsFirst Keypad Options Second Keypad OptionsKeypad Function Key Programming Programming Descriptions002 Zone Definitions O Programming Zones/PGMs Installer CodeSystem Times Master CodeSecond System Options First System OptionsThird System Options Tenth System Options Fourth System OptionsOFF Keypad Always Active. The keypad does not blank Standard Time Set Clock Back Zone Loop Response Options134 Zone Attributes Daylight Saving Time Move Clock AheadCall Waiting Cancel String PGM Output TimerCross Zone/Police Code Timer No Activity Arm TimerTest Transmission Time Communicator VariablesFirst Communicator Options First Downloading Options OFF Closing Confirmation Disabled. The keypad does not beepSecond Communicator Options Third Communicator OptionsNumber of Rings to Answer On Downloading Access CodeDownloading Computer Phone Number Panel Identification CodeWay Audio Control Options applies to SCW9047 only Automatic Clock AdjustFollowing attributes are available for PGM Output Type Second International Options Delay Between Dialing AttemptsWireless Programming First International OptionsRestore Wireless Device Default Programming Wireless Module Placement TestInstaller Lockout Enable Installer Lockout DisableKeypad Programming Fire Alarm LabelsAlarm when Armed Event Message 069 Command Output LabelOption Description Future Use OFF Power LED is disabled. Option 6 has no effectFirst Keypad Options Second Keypad OptionsProgrammed LCD Message Duration Label ResetThird Keypad Options Programmed LCD MessageTesting & Troubleshooting Trouble 8 Loss of Clock/Date Trouble 4 Failure to CommunicateContact ID Appendix a Reporting Code FormatsSIA Format Automatic Zone Alarm/Restoral Codes Contact ID Zone Alarm/Restoral Event CodesAppendix B Communicator Format Options Residential Dial PagerNorth America Appendix C Regulatory Approvals InformationEurope SIA False Alarm Reduction InstallationsNew Zealand Exit Time Appendix D SIA False Alarm ReductionFormat Reporting Code/Event Appendix E 2-Way Audio Verification SCW9047 onlyBell/Buzzer Silent During 2-Way Audio Key Command DescriptionVOX Support Hang-up Auto-detectionPage FCC Compliance Statement