DSCover Satellite Products SCW904x manual Before Installing The Equipment

Page 2

SAFETY INSTRUCTIONS for SERVICE PERSONNEL

WARNING: When using equipment connected to the TELEPHONE NETWORK, there are basic safety instructions that should always be followed. Refer to the SAFETY INTRUCTIONS provided with this product; save them for (future) reference. Instruct the end-user regarding the safety precautions that shall be observed when operating this equipment.

Before Installing The Equipment

Do NOT use a sharp or metal object to open the packaging!

Ensure your package includes the following items:

User’s Guide (Manual) including the SAFETY INSTRUCTIONS.

READ and SAVE These Instructions!

Follow All WARNINGS AND INSTRUCTIONS specified within these Instruction and/or on the equipment.

Equipment SCW904x

Power Supply, Direct Plug-In

Mounting Hardware.

Selecting A Suitable Location For The Alarm Controller

Use the following list as a guide to find a suitable place for this equipment:

Locate it near a telephone socket and a power outlet.

Select a place that is free from vibration and shocks.

Place the Alarm Controller on a flat, stable surface and follow the Installation suggestions.

Do NOT locate this product where persons will walk on the secondary circuit cable(s). Do NOT use extension cords to PLUG-IN the Power Supply of this equipment.

AVOID setting up the equipment near heaters, air conditioners, ventilators, and/or refrigerators Do NOT connect the Alarm Controller to electrical outlets on the same circuit as large appliances.

Do NOT select a place that exposes your alarm controller to direct sunlight, excessive heat, moisture, vapors, chemicals or dust.

Do NOT install this Equipment near water. (e.g., Bath Tub, Wash Bowl, Kitchen/Laundry sink, In a wet basement, or near swimming pool, etc.). Do NOT install this equipment and its accessories in areas where there is a risk of explosion.

Do NOT connect this Alarm Controller to electrical outlets controlled by wall switches or automatic timers; avoid interference sources.

SAFETY Precautions required during Installation:

NEVER install this EQUIPMENT and/or TELEPHONE WIRING during A Lightning Storm!

NEVER touch uninsulated Telephone wires or Terminals unless the telephone line has been disconnected at the network interface.

Ensure that Cables are positioned so that accidents can not occur. Connected Cables must NOT be subject to excessive mechanical strain

Use Only the Power Supply supplied with this equipment. Use of unauthorized power supplies may cause damage.

The AC Socket/Outlet powering the equipment shall be located near the equipment and shall be easily accessible.

WARNING:

THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS INTENDED TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST BE QUICKLY DISCONNECTED. IT IS IMPERATIVE THAT ACCESS TO THE MAINS PLUG AND ASSOCIATED MAINS SOCKET/OUTLET, IS NEVER OBSTRUCTED.

WWW.DIYALARMFORUM.COM

Image 2
Contents Installation Guide Safety Precautions required during Installation Before Installing The EquipmentSelecting a Suitable Location For The Alarm Controller Table of Contents Page Installation & Wiring Technical SummaryInstallation Ensure connector key is oriented correctlyMax wire Length to End-of-line Resistor WiringBurglary Zone Wiring Chart Self Contained Wireless Alarm System Activate Wireless Device Wireless Device EnrollmentEnter Wireless Enrollment Mode Verify Device Electronic Serial Number ESNZone Dependant Devices Detectors Template Programming Zone Definitions Options 1Digit 3 selects 1 of the 8 following options Installer Lead-in/Lead-out and DLS Lead-in/Lead-out DLS Programming New Installations Refer to .1 Installation onExisting Installations Refer to .1 Installation on Local Programming with PC-LinkOperation Trouble Display Alarm Memory DisplayDoor Chime Enable/Disable Program User CodesAdditional Keypad Functions 7x Command Outputs 1&2Installer Programming 9User Code No-Entry ArmingAdvanced Programming Programming Work Sheets Index to Programming Work Sheets and DescriptionsFunction Key Options Programming WorksheetsFunction Key Programming Zone Definitions009 I/O Programming Installer’s Code Master CodeSystem Times Keypad Lockout OptionsFourth System Options Second System OptionsThird System Options Tenth System OptionsZone Loop Response Options Zone Attributes Options 10-13 are reserved for Future UseNo Activity Arming Pre-alert Timer PGM Output TimerCross Zone/Police Code Timer No Activity Arming TimerMiscellaneous Alarm Reporting Codes Alarm Reporting Codes, ZonesAlarm Restoral Reporting Codes, Zones Priority Alarm and Restoral Reporting CodesMiscellaneous Opening Disarming Reporting Codes Tamper Reporting Codes, ZonesTamper Restoral Reporting Codes, Zones Opening/Closing Communicator Call Directions Tamper/Restore Communicator Call DirectionsCommunicator Format Options Communication Variables System Maintenance Communicator Call DirectionsSystem Test Transmissions Communicator Call Directions Test Transmission Time of DayDownloading Options Second Communicator OptionsThird Communicator Options PGM Output Attributes Number of Rings To Answer OnInitiate PC-Link Downloading Attribute600 2-way Audio Control Options Applies to SCW9047 only Automatic Clock AdjustDelay Between Dialing Attempts First International OptionsWireless programming Wireless Zone Programming Wireless Supervisory WindowInstaller Lockout Disable General Wireless OptionsWireless Module Placement Test Installer Lockout Enable Restore Wireless Device Default ProgrammingLocal Keypad Programming Label Programming ZoneCommand Output #1 Label Fire Alarm LabelAlarm When Armed Event Message Command Output #2 LabelSecond Keypad Options Reset Programmable Labels to Factory DefaultsFirst Keypad Options Third Keypad Options002 Zone Definitions Programming DescriptionsKeypad Function Key Programming Master Code Installer CodeSystem Times O Programming Zones/PGMsThird System Options First System OptionsSecond System Options OFF Keypad Always Active. The keypad does not blank Fourth System OptionsTenth System Options Daylight Saving Time Move Clock Ahead Zone Loop Response Options134 Zone Attributes Standard Time Set Clock BackNo Activity Arm Timer PGM Output TimerCross Zone/Police Code Timer Call Waiting Cancel StringFirst Communicator Options Communicator VariablesTest Transmission Time Third Communicator Options OFF Closing Confirmation Disabled. The keypad does not beepSecond Communicator Options First Downloading OptionsPanel Identification Code Downloading Access CodeDownloading Computer Phone Number Number of Rings to Answer OnFollowing attributes are available for PGM Output Type Automatic Clock AdjustWay Audio Control Options applies to SCW9047 only First International Options Delay Between Dialing AttemptsWireless Programming Second International OptionsInstaller Lockout Disable Wireless Module Placement TestInstaller Lockout Enable Restore Wireless Device Default Programming069 Command Output Label Fire Alarm LabelsAlarm when Armed Event Message Keypad ProgrammingSecond Keypad Options OFF Power LED is disabled. Option 6 has no effectFirst Keypad Options Option Description Future UseProgrammed LCD Message Label ResetThird Keypad Options Programmed LCD Message DurationTesting & Troubleshooting Trouble 4 Failure to Communicate Trouble 8 Loss of Clock/DateAppendix a Reporting Code Formats Contact IDContact ID Zone Alarm/Restoral Event Codes SIA Format Automatic Zone Alarm/Restoral CodesAppendix B Communicator Format Options Pager Residential DialAppendix C Regulatory Approvals Information North AmericaNew Zealand SIA False Alarm Reduction InstallationsEurope Appendix D SIA False Alarm Reduction Exit TimeAppendix E 2-Way Audio Verification SCW9047 only Format Reporting Code/EventHang-up Auto-detection Key Command DescriptionVOX Support Bell/Buzzer Silent During 2-Way AudioPage FCC Compliance Statement